A large-particle composite consisting of tungsten particles within a copper matrix is to be prepared. If the volume fractions of tungsten and copper are 0.60 and 0.40, respectively, estimate the upper limit for the Young's modulus of this composite. Modulus of Elasticity of: Copper: 110 GPa; Tungsten 407 GPa Type your answer as XXX

A large-particle composite consisting of tungsten particles within a copper matrix is to be prepared. If the volume fractions of tungsten and copper are 0.60 and 0.40, respectively, estimate the upper limit for the Young's modulus of this composite. Modulus of Elasticity of: Copper: 110 GPa; Tungsten 407 GPa Type your answer as XXX

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using the table below, estimate the components of the matrices and develop the stiffness and compliance matrices for an orthotropic lamina of E-glass/470-36 E-glass/vinylester.
Nylon 6,6 is a thermoplastic polymer with high mechanical strength, high resistance to chemical environments, and good stability under heat. Therefore, it is well suited to be used in 3D structural objects. A cylindrical nylon 6,6 pipe is made by injection molding. The pipe is 1 m long with an outer diameter of 8cm, and a thickness of 2mm. The crystallinity of the pipe is 25%. The density and associated percent crystallinity for two nylon 6,6 samples are measured as below: ρ(g/cm3) crystallinity (%) 1.190 67 1.155 44 If the degree of polymerization is 500, calculate the number of chains in the pipe. (Assume the chains are equal in length).
Nylon 6,6 is a thermoplastic polymer with high mechanical strength, high resistance to chemical environments, and good stability under heat. Therefore, it is well suited to be used in 3D structural objects. A cylindrical nylon 6,6 pipe is made by injection molding. The pipe is 1 m long with an outer diameter of 8cm, and a thickness of 2mm. The crystallinity of the pipe is 25%. The density and associated percent crystallinity for two nylon 6,6 samples are measured as below: ρ(g/cm3) crystallinity (%) 1.190 67 1.155 44 Calculate the density of this pipe, which has 25% crystallinity.
Calculate the Degree of Crystallinity of the composite having mineral particles of 15(%) by weighthas enthalpy of melting of 31.3 (J/g) and enthalpy of crystallization of 24.4 (J/g). if, Δhm100 = 90(J/g). The Specific gravity of the matrix and particles is 1.24 and 2.2 respectively.
A ceramic component with Young’s modulus of 300 GPa and a KIc of 4 MPa.m1/2 is to survive a water quench from 500°C to room temperature of 25°C. If the largest flaw in that material is on the order of 2 μm, what is the maximum value of thermal expansion coefficient (α) for this ceramic required to survive the quench? Assume that there are 20 flaws of 2 μm size. Poisson ratio of the ceramic material is 0.25.
A polymer sample of height 700 cm with an area of 6 m2 supports a mass of 70 tons. Youngs modulus of the polymer sample is found to be 60 GPa. Calculate the change in height of the polymer sample, applied stress and strain.
A Cotton fiber, initially 2.2 cm long, is being stretched to its maximum known strain. What would be its final length, in cm, before rupture?
The mechanical properties of matrix A may be improved by incorporating fine particles of B. The moduli of elasticity of these materials are, respectively, 79 GPa and 493 GPa, determine the composite lower bound modulus of elasticity if the volume fraction of the matrix is 0.75
A ceramic with KIc = 4 MPa m1/2 contains pores with radius a = 5 µm due to incomplete sintering. These pores lead to a decrease in the failure stress of the material in both tension and compression. One in every ten grainboundary junctions contains a void; the grain size of the ceramic is 50 µm. The ceramic fails in compression when the length ℓ of each crack generated at the voids equals one-half of the spacing between the voids. (a) Determine the compression strength of the ceramic, using the equation from Sammis and Ashby. (b) Determine the tensile strength of the ceramic, assuming flaws with size a.
Consider a dispersion strengthened alloy with average interparticle spacing of L. If Nv is he number ofparticle per unit volume, d is the particle dimeter, and Vp is the volume fraction of particle, then whatwill be the expression for interparticle spacing in term of the particle diameter and volume fraction?
A large-particle composite consisting of tungsten particles within a copper matrix is to be prepared. If the volume fractions of tungsten and copper are 0.70 and 0.30, respectively, a) Compute the modulus of elasticity of this composite in the longitudinal direction. (The upper limit) and the modulus of elasticity in the transverse direction. (The lower limit), given the data that follow. Modulus of Elasticity (GPa) Copper 110 Tungsten 407 b) If the cross-sectional area is 280 mm2 and a stress of 60 MPa is applied in this longitudinal direction, compute the magnitude of the load carried by each of the fiber (tungsten) and matrix (copper) phases.
Question 1 A composite material consists of 40% parallel carbon fibres with a Young’s modulus of 405 GPa in a matrix of epoxy resin with a Young’s modulus of 2.5 GPa. Calculate the Young’s modulus of the composite in the parallel and in the perpendicular directions of the fibres. Use the graphical method seen in class to show the possible value of the overall young modulus of your composite material.