A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B. calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer-110 mm, R=695 mm, 0 = 24° Detail of contact at B Answer: I mm

A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B. calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer-110 mm, R=695 mm, 0 = 24° Detail of contact at B Answer: I mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.72P

See similar textbooks

Similar questions

The 3600-lb car with rear Wheel drive is attempting to tow the 4500-lb crate. The center of gravity of the car is at G, and the coefficients of static friction are 0.6 at B and 0.2 at C. Determine if the crate will slide.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
Can the uniform bar of weight W remain at rest in the position shown?
The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 710 kg and an average gear-tooth force of 2.75 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset x¯ of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers.Assume r = 140 mm, R = 515 mm, θ= 25°.
The solid homogeneous cylinder shown has a mass of 30 kg and is rotating at 1200 rpm clockwise about a fixed horizontal axis through O. The coefficient of kinetic friction between the brake and the cylinder is 0.20. If the tension in the spring when the brake is applied is 100 N, determine the time required for the cylinder to stop rotating. Neglect the thickness of the vertical members. (Draw FBD)
The table lamp consists of two uniform arms, each weighing 4N, and a 10-N bulb fixture. If θ = 16°, calculate the couple CA that must be supplied by the friction in joint A.
In the given 15.0 meter slab and inclined 10degrees with the horizontal, the ends are resting on inclines of 30degrees incline at B and 20degrees at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be the front wheels located before motion impends, the angle of friction is 15degrees for all areas of contact. Neglect the weight of the slab.
A ball is shot at high speed into a frictionless channel that is in the shape of a segment of a circle with center at O.The channel is frictionless and sits on a horizontal table top.The figure shown is the top view.Which of the following force(s) are acting on the ball when it is within the frictionless channel at position B? Explain your answers.Check all that apply.1- A downward force of gravity.2- A force pointing from O to B.3- A force in the direction of motion.4- A force pointing from B to O.
The thin rectangular bar AIB has mass m. Determine the intensity of the normal force at A and the intensity of the reaction j of the pin O. The friction of the support pin O is negligible if the alpha angle is 51 degrees