The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (a) Determine the maximum bending stresses (T & C) and absolute maximum transverse shear stress (b) Check if the beam is safe if the allowable bending stress (T & C) = 120 MPa and the allowable shear stress = 80 Mpa 10 kN/m 4.0 m 4.0 m P= 20.52 kN T tw Section Properties: b=320 mm d = 350 mm tf = 20 mm tw = 20 mm

The simple beam with overhang carries a uniform load, w (kN/m) and a force P (kN). (a) Determine the maximum bending stresses (T & C) and absolute maximum transverse shear stress (b) Check if the beam is safe if the allowable bending stress (T & C) = 120 MPa and the allowable shear stress = 80 Mpa 10 kN/m 4.0 m 4.0 m P= 20.52 kN T tw Section Properties: b=320 mm d = 350 mm tf = 20 mm tw = 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5-m propped beam carries a uniformly distributed load equal to 45 kN/m applied throughout the beam. If the reaction at the roller is 84.375 kN, what is the maximum flexural shear stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa)
A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
g.) What is the moment of inertia (I) about the neutral axis of the section? (in mm^4) h.)What is the first moment of an area (Q) about the neutral axis of the section? (in mm^3) i.)What is the maximum shearing stress (fv) of the beam? (in MPa)
1. A 75 mm x 75 mm x 8 mm angle is used as a beam over a span of 7.0 m. It is subjected to loading of 10 kN/m acting in the vertical plane passing through the centroid of the Section Determine maximum stress induced in the section.
A W460×60 steel beam is loaded as shown. Assume w = 40 kN/m, M0 = 60 kN·m, LAB = 3.9 m, LBC = 1.6 m, E = 200 GPa, and I = 255 x 106 mm4.(a) Determine the reaction force at roller B.(b) Determine the maximum positive bending moment in the span.(c) If the allowable bending stress is 210 MPa, determine the minimum acceptable section modulus for the steel beam. Remove roller B. Determine the deflection at point B caused by the distributed load vw and by the moment vMo. Upward deflection is positive.Answer:vw = mmvMo = mm
A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a length of 3 m. The pipe is fixed at the bottom and free on top and is subjected to a torque of 25 Kn-m and lateral force 39 kN. G = 78 GPa. Calculate the maximum angle of twist in degrees, maximum shear stress due to torque, maximum shear stress due to lateral force, and maximum flexural stress.
Solve using method of consistent deformation; EI =4x10^6 KN m^2, L=3.0, Wo=20KN/m
The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P = 40 kN. Follow the sign convention. a) Although it is not very accurate, use the shear formula to determine the shear stress developed at point A b) Determine the principal stress σ1 at point A c) Determine the principal stress σ2 at point A
If the T-beam is subjected to a vertical shear V = 14 kips, determine the maximum shear stress (ksi) in the beam Where: tf = 2.4 in and d = 7 in