A lever with a mechanical advantage of 6 is attached to the pump piston of a hydraulic press. The area of the pump piston is 1.2 in2 and that of the output piston is 18 in2. A) If the press is 75% efficient, find the force the output piston exerts when a force of 30 lbs is applied to the pump lever.

Lever with mechanical advantage attached to the pump piston =6. The area of the pump piston is,…

Answered: ) | bartleby

Engineering

Mechanical Engineering

)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: Find the equivalent stresses at points (1) and (2) in the loading case in the figures below. Which i...

Q: Question (2). The following system has a block of a mass m = xykg(from your registration mumber), st...

Q: Air is contained in a frictionless piston-cylinder assembly as shown below. The initial equilibrium ...

A: Given Data Diameter of the piston, dc=00.452 m Mass of piston, m=200 kg Atmospheric pressure, Patm=...

Q: 5. A spark-ignition engine operates on the ideal Otto cycle. The air enters the engine at 101 kPa an...

Q: The question in the photo

A: Given:Demand=50000 units/yrordering cost, Co=Rs. 3/orderholding cost,Ch=12+0.06+0.004 =Rs. 12.064sho...

Q: 22.12 What is a cermet? What are its advantages?

A: Cermet is basically a composition or combination of metals and ceramics.

Q: The following system is oscillating under the action of a moment M = 20 sin(3t), it consists of a bl...

Q: In an Otto cycle, the volume at the beginning of the isentropic compression is 0.8 L. If the displac...

A: Basics of Otto cycle.

Q: Just solve branch 4

A: According to the given information we have d2 which I distance of mass m from the point O O=2×L22...

Q: Oscillations in a U-shaped tube We consider a U-shaped tube of width L initially filled with a fluid...

Q: You need to buy groceries at the supermarket, deposit a check at the credit union, and purchase a bo...

Q: Q1) For force system shown in the figure below, find the following: 1- Resultant force 2- The locati...

A: given:

Q: Q.(a)Derive the tension ratio of the belt drive. (b) Define the slip and show the effect of slip o...

A: Part (a) Let T1= Tension in the belt on the tight side, T2= Tension in the belt on slack side,...

Q: 2 2 .19 Make a list of the alloying elements used in high-speed steels. Explain w hat their function...

Q: A traveling wave on a taut string with a tension force T is given by the wave function: y(x,t) = 0.1...

Q: In an oscillatory motion of a simple pendulum, the ratio of the maximum angular acceleration, e"max,...

A: Given relation,

Q: Describe the material behavior of Steel

A: Material behaviour of steel 1. Ductility: The ductility of steel can be changed by changing the per...

Q: A simple pendulum is made of a 50 cm-string and a bob of mass m. At t = 0, the pendulum is at its eq...

Q: In a Diesel cycle, the air at the beginning of the isentropic compression is at 1 bar. The volume at...

A: We are suppose to solve only 3 subparts. Please post other parts as a separate question.

Q: A load of F = 14kN is applied to a circular chain link in the figure. Since σem = 600 N / mm2What is...

Q: List some five factors that influence machine design

A: Machine design: The machine design is the iterative decision-making activity to produce a plan or dr...

Q: In an Otto cycle, the volume at the beginning of the isentropic compression is 0.74 L. If the displa...

Q: A mass-spring system oscillates on a frictionless horizontal surface in simple harmonic motion with ...

A: Given that the amplitude a=0.2 let the spring constant=k

Q: P2. A uniformly tapering rectangular rod is subjected to load as shown in the figure . Determine the...

Q: Obtain the equations of motion of the system given below by the law of energy conservation.

Q: Heat transfer

A: The expression for the total thermal resistance of the house wall is given by as follows

Q: Use Lagrange’s equation to determine the equation of motions of Fig (a and b)

Q: 22.9 Explain how cutting fluids penetrate the tool-chip interface.

Q: A block-spring system has a maximum restoring force Fmax = 0.1 N. If the amplitude of the motion is ...

Q: Physiques

Q: Determine the maximum torque that can be applied to the shaft, given that the maximum angle of twist...

A: GIVENθ=0.0225 rad'a' section 1=2 m'a' section 2=1 m

Q: A 25 kg mass sliding on a horizontal frictionless floor at 10 m/s rams a spring that is attached to ...

Q: A block attached to a spring, oscillates on a frictionless horizontal surface with a period of 0.45 ...

A: Given: The time period, t = 0.45 S The initial amplitude, x = A The final amplitude, X = - A/2

Q: In a commercial steel pipe of diameter 0.01906 (in meters), industrial waste water (approximate as w...

A: Given Data: The diameter of the pipe is, D=0.01906 m. The average velocity of water is, V=30 m/s.

Q: A mass-spring system oscillates on a fridtionless horizontal surface in simple harmonic motion with ...

Q: Hydrodynamics pumps (WRITE LEGIBLY) 3. A centrifugal pump, operating at a speed of 1750 rpm and brak...

A: Given:For 1st centrifugal pump ,N=1750 rpmrate of flow, Q=600 gpmh=104 ftimpeller diameter, D=10 inc...

Q: Given an ideal diesel cycle with compression ratio of 16.2, cut-off ratio of 2.05, Determine the mea...

A: Assumptions: 1. The air-standard assumptions 2. Kinetic and potential energy changes are negligible....

Q: 16. A 12 cm diameter long bar initially at a uniform temperature of 40°C is placed in a medium at 65...

A: Check for the lumped analysis : Bi=hkLL=VAs=π4×D2×LπDL=D/4=0.12/4=0.03Bi=2220×0.03=0.033<0.1 Bi...

Q: Just solve branch 4

Q: Obtain the equations of motion of the system given below by the law of energy conservation.

Q: In a Dual cycle, the volume at the beginning of the isentropic compression is 0.88 L and the pressur...

Q: 75 kN Composite A-36 steel bar shown made from two segments AB and BD. Area A= 600 mm² and Agp=1200 ...

Q: 22.4 Why are some tools coated? What are the common coating materials?

A: Let us discuss about reasons for tool coating in detail.

Q: The wavefunction of a mechanical wave on a string is described by: y(x,t) = 0.012sin(Ttx- 100Ttt+2Tt...

A: Solution is given below.

Q: Q2: Replace the 100 Ib f Force of Figure below into horizontal and vertical components for each of t...

A: Given": F= 100 lb Solution: For the angle -35°(as angle is in 4th quadrant ): Fx=100cos(-35°)=81.91 ...

Q: Consider a place where the gravity is one-fourth the gravity on Earth (g' = g/4), then the frequency...

A: Given data g' = g/4

Q: The centre of mass of a non-uniform rod of length 4 m whose mass per unit length is K = 3x kg/m, whe...

A: The mass per unit length is, K=3x kg/m The length of a rod is, L=4 m

Q: A 250 g ball collides with a wall. The figures below show the ball’s velocity and force exerted on t...

Q: Evaluate the pitch diameter (in mm) of gear E.

A: Given: NA=18mA=mB=2 mmdB=108 mmmC=mD=mE=mF=3 mmNC=24nD=120 rev/minNf=16nF=480 rev/minnA=720 rev/min

Q: A spark-ignition engine operates on the ideal Otto cycle. The air enters the engine at 101 kPa and 3...

A: initial pressure (P1 ) = 101 kPa initial temperature (T1 ) = 32 °C = 32 + 273 = 305 K temperature af...

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A lever with a mechanical advantage of 6 is attached to the pump piston of a hydraulic press. The area of the pump piston is 1.2 in² and that of the output piston is 18 in². A) If the press is 75% efficient, find the force the output piston exerts when a force of 30 lbs is applied to the pump lever.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A train has a weight of 100 tons (2,000lbf) is stopped from 4 mph in 1 ft by a hydraulic cushion.If rolling friction is 0.05 of the car weight, Find: • The stopping force using the gs method • The stopping force using the energy method
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
A force of 98 N is applied to the input piston of a hydraulic system. The area of the input piston is 22 cm2, and that of the output piston is 70 cm2. Find how far the output piston moves if the input piston moves 2 cm per stroke.
A 10 ft chain weighs 35 lb and hangs from a ceiling. Find the work done (in ft-lb) in lifting the lower end of the chain to the ceiling so that it's level with the upper end.
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
A 200 N block slides down at an inclined surface at an angle of 50 degrees with the horizontal. Neglecting friction, find the force that causes the block to slide.
In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and 100 cm. Find the distance moved by the load piston if 10 strokes are applied to the effort piston . Given : Stroke length of the effort piston is : 50 cm . Distance moved by Load piston : ____________m
2. A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall.Find the forces exerted by the wall and by the ground on the ladder.
Find the compression length of a spring if a 100 pound weight if dropped from 8 ft onto a spring with constant of 33.33 lb/in. The correct answer is 2.266 ft.
A riveting machine is driven by a 4 kW motor. The moment of inertia of the rotating parts of the machine is equivalent to 140 kg-m2 at the shaft on which the flywheel is mounted. At the commencement of operation, the flywheel is making 240 r.p.m. If closing a rivet occupies 1 second and consumes 10 kN-m of energy, find the reduction of speed of the flywheel. What is the maximum rate at which the rivets can be closed?
A cable that weights 2 lb / ft is used to lift 800 lb of coal up a mineshaft 500 ft deep.Find the work done.
A piston cylinder system contains a gas which expands under a constant pressure if 1200 lb/ft3. If the piston is displaced 1 ft during the process, and the piston diameter is 2 ft. What is the work done by the gas on the piston? (with drawing to fully understand the question)a) 1768 ft-lb c) 3768 ft-lbb) 2387 ft-lb d) 4000 ft-lb