F 30° ød. 2 M. 10

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse…

A:

Q: 90 MPa 60 MPa 20 MPa

A: Given, Normal stress in x-direction = σx = -20 MPa Normal stress in y-direction = σy = 90 MPa Shear…

Q: Find the stresses at points A andB on the plate shown in the figure.

A: The normal stress at the points A and B can be determined as,

Q: 6. In a plane stress condition, the components of stress at a point are o, =20 MPa, oy =80 MPa and…

A:

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

A:

Q: Q2: A șteel pipe with an outside diameter of (95 mm) and an inside diameter of (85 mm) supports the…

A:

Q: 2. Assume the plane stress state: ơ1 = 50, 02 = -250, T12 = 150 (all stresses in MPa). 2.1. Sketch…

A: σ1=50MPa σ2=-250MPa τ12=150MPa To Find Mohr's Circle Principal stress and their direction Maximum…

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: -  The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: Estimate the normal stress (on) and shear stress (t) on the inclined plane as shown in the below…

A:

Q: 4. Find the average normal stresses on members AB, BE, and EG, If the area of all members is 1200mm…

A: In a truss, the force in each member can be determined using method of joints of sections. Force…

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

A:

Q: Find the maximum shear stress if maximum principal stress is 30 MPa Minimum principal stress 20 Mpa

A:

Q: 2. The hollow cylinder is fixed at the wall and pressurized at p = 2,000 Pa. Its outer diameter (OD)…

A: For the given cylinder the following are the reasons for creating stress at point A: compressive…

Q: 350 mm, tw = 7 mm, and h = 117 mm. Determine the principal stresses and the maximum shear stress…

A:

Q: Draw Mohr circle for the given stress state Find o1, 02 and R (Tmax) Txy = 40 MPa o, = 50 MPa = 30…

A: Given data:- Stress in x-direction, σx=50MPaStress in y-direction, σy=-30MPanegative for compressive…

Q: N.6.1. Find principle stress if the values are as given: Upper side stress:300lb/9pulg2 Tangential…

A: Given Data and Initial Calculation:-

Q: Find the maximum shear stress for the stress case given in the figure.

A: Given Data The stress acting in x direction is: σx=100 MPa The stress acting in y direction is:…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 50 m long. α = 11.7 ×…

A: Temperature, T1= 15∘C Rail length, L= 50 m α= 11.7×10-6/∘C E= 2.3×105 N/mm2 Expansion allowance, ∆=…

Q: What is the maximum shear stress RESULTING FROM THE COMBINATION OF THE FOLLOWING stresses: Tesile…

A: Given data: Sx=200 MPaSy=100 MPaSS=50 MPa Need to determine the maximum shear stress.

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, ơy = 80 MPa and txy…

A: Given, Stress in x-direction = σx = 20 MPa Stress in y-direction = σy = 80 MPa Sheat stress in…

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: If the principle stresses in a plane stress problem are 100 MPa and 40 MPa, then maximum shear…

A: As given in the question, Maximum principal stress = σ1 = 100 MPa Minimum principal stress = σ2 = 40…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress…

A: Given that, Normal stress in x-direction, σx=80 MPa,Normla stress in y-direction, σy=-40 MPa,Shear…

Q: L 10 kN 7 kN 14 kN H 240 mm The pipe in the figue problem is subjected to the forces given in the…

A: Given: The load acting on pipe along y-axis, Py = 10 kN The load acting on pipe along x-axis, Px =…

Q: A pressure vessel with an internal pressure of 400 psi is fixed at one end. At its free end, two…

A: Px=10kipsPy=15kipsPz=5kipsD=10 ind=9.6 in

Q: Find the stresses at points A and B on the plate shown in the figure.

A: The normal stress on the point A can be determined as,

Q: The normal stresses at a point are o, = 80 MPa and oy = 20 MPa; the shear stress at this point is…

A:

Q: Find the stresses in A, B and C? And Vem 6m 0.006 MN cm B -Ha 4m 1 6cm

A: ◆ Stress in A : 1 MPa ◆ Stress in B : 1.67 MPa ◆ Stress in C : 1 MPa

Q: uniformly distributed stresses acting on the side faces plate are b = 10 in. t = 0.75 in.., E =…

A: Given data  Width (b) = 690mm = 69*10-³m Thickness (t) = 40mm = 40*10-³m  E = 41 Gpa = 41*10⁹ V =…

Q: A rail line is laid so that there is no stress in rails at 15°C. The rails are 500000 mm long. α =…

A:

Q: The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress…

A: Given: Applied stresses are: Sx = 80 MPa, Sy = 40 MPa, and Sxy = 75 MPa Angle is β=51∘.

Q: If o, = 30 ksi, ơy = 20 ksi, and Txy = 10 ksi, what is the maximum in-plane shear stress in ksi? %3D

A:

Q: 1 MPа 2- For the state of stress as shown below, 2 МPа a) Find principal stresses З МРа b) Draw…

A:

Q: For the element shown find 1) Principle stresses and their direction 2) Shear stresses and their…

A:

Q: Question 3) Plane stress state ata point is given in the figure. L. a) Calculate the principal…

A: τxy=10 MPaσ1,2=σx+σy2±σx-σy22+τxy2 Since it is case of pure shear so σx=0 &…

Q: For the state of stress shown in the figure, determine the stress component Txy so that the maximum…

A:

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPA 24 10 20 MPa The stresses…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: Dmm Ø20 0,1 Ø10 20 2. Draw diagram of normal stresses.

A: Here bending stresses will be normal stresses. The normal stresses diagram drawn in step 2.

Q: Find the maximum shear stress at a plane if the major and minor principal stresses at a point are 3…

A:

Q: Calculate the normal stress and shear stress acting on the plane 2x+y+2z=1 passing thorough a point…

A: given; plane ;2x+y+2z=1stress at point (σ)=162022000023

Q: A state of stress at a point A is given by σx = -75 MPa, σy = 122 MPa, and τxy = -3.75 MPa. Which of…

A: Given    σx = -75 MPa   σy = 122 MPa  τxy = -3.75 MPa

Q: For the framc shown in the figure, Find the normal and shear stresses based on the following…

A: Given: The diameter of the pin at A, d = 10 mm The diameter of the pin at C, D = 15 mm

Q: 1) ) The curve of stress versus time on the cross section of engine connecting rod is shown in the…

A:

Q: 150 kN A 500 mm ISOKN T=50 kN.m

A: Solutions: Moment of inertia of the rod=π×d464=π×0.04464=1.2566×10-7m4 Bending moment at…

Q: A cylinder consists of an outer tube of internal and external diameters of 16 cm and 18 cm…

A: We know that a cylinder is made up of an inner tube with an internal and external diameter of 8 cm…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 14MPª لاخرين 24 1 10 2 20 МРа…

A: Given Normal stress at X axis = 20 MPa Normal stress at Y axis = 14 MPa Slope of plane = 24 and 10…

Q: Try

A: Given Data : σx=60 MPa σy = 0 τxy = 40 MPa.

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.