Answered: A light bulb is rated at 30 W when…

A light bulb is rated at 30 W when operated at 120 V. How much charge enters (and leaves) the light bulb in 9.4 min? Select one: a. 169.20 b. 141.00 c. 84.60 O d. 103.40 e. 112.80

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter28: Current And Resistance

Section: Chapter Questions

Problem 57PQ

See similar textbooks

Related questions

Q: *37 An unknown resistor is connected between the terminals of a 3.00 V battery. Energy is dissipated…

A: Given: Case-I: The terminal voltage across the resistance is 3 V. The power loss across the resistor…

Q: The batteries shown in the circuit in the following figure have negligibly small internal…

A: Please see the answer below.

Q: Two lightbulbs both operate on 120 V. One has a power of 25 W and the other 100 W. Which lightbulb…

A: Potential difference, V = 120 V Power of the first lightbulb, P1 = 25 W Power of the second…

Q: A lightbulb has a resistance of 240 when operating with a potential difference of 120 V across it.…

A: SOlution: Given that R = 240 Ohm V = 120 V

Q: Two lightbulbs both operate on 220 V. One has a power of 100 W and the other 60 W. Which lightbulb…

Q: What is the resistance of a light bulb if 0.50 A flows through it when 120 V is connected across it?

A: As per the answering guidelines we will solve only first problem. Please upload the other problems…

Q: An unknown resistor is connected between the terminals of a 3.00 V battery. Energy is dissipated in…

Q: . A battery is rated at 12 V and 160 A-h. How much energy does this battery store? Answer: 6.9 MJ

A: Given that---- V = 12 volt I = 160 amp t = 1 hour Question ❓ Energy of battery ?

Q: An electrical bulb draws a current of 5A when connected to a 400 resistor. Keeping the voltage…

A: Initial Current =5A Resistance = 40ohm using ohms law:

Q: A light bulb is rated at 30 W when operated at 120 V. How much charge enters (and leaves) the light…

A: Given data: Power (P) = 60 W Voltage (V) = 120 V Time (t) = 1.0 min = 60 seconds Required: The…

Q: 5. A 60.0-W lamp is placed in series with a resistor and a 120.0-V source. If the voltage across the…

Q: An 1,840 W toaster, a 1,340 W electric frying pan, and a 95 W lamp are plugged into the same outlet…

A: Given Data Power of the toaster is Ptoaster=1840 W Power of the frying pan is Ppan=1340 W Power of…

Q: A teapot with a surface area of 335 cm2 is to be plated with silver. It is attached to the negative…

Q: A car owner forgets to turn off the headlights of his car while it is parked in his garage. If the…

Q: A 5.00 V power supply provides a maximum current of 11.5 A. (a) Calculate the maximum power…

A: Potential difference provided by the supply (V) = 5 volts Maximum current (I) = 11.5 A

Q: Using this information, estimate the following quantities (a) total amount of charge transferred…

Q: An electrical bulb draws a current of 5A when connected to al 400 resistor. Keeping the voltage…

Q: A V = 7.58 V battery is connected to a R = 52.2 Ω resistor. How much current (I) runs through the…

A: Given, V =7.58 V R =52.2 Ω . We have to find the current (I) that runs through the resistor. Let's…

Q: An electric device delivers a current of 10 A for 10 seconds. How many electrons (1.6x10-19C) flow…

A: Given, Current (I) =10A Time(T) =10 seconds We know, Charge(Q) = I * T Q= 10* 10 =…

Q: The femoral artery is the large artery that carries blood to the leg. A person's femoral artery has…

Q: In the circuit below, R = 2000 Ω and ε = 200 v. What is the current from “a” to “e”? a) 50 mA…

A: From Kirchhoff's node rule net incoming current must be equal to net outgoing current at any…

Q: A 5.1 A current is set up in a circuit for 4.7 min by a rechargeable battery with a 6.0 V emf. By…

A: Given:- Current (I)=5.1 A Time(T) =4.7 min emf(V)=6.0 V Find:- How much chemical energy of the…

Q: A device experiences a voltage drop of 4.0 V across it while a current of 4.0 mA flows through it.…

A: The power dissipated in a device is the product of the current and the voltage drop.

Q: Two resistors are connected in parallel with a 9.00-V battery Complete the table below. For all the…

A: In parallel combination potential difference remains same

Q: 7. a. In a car electrical system, the capacity of a storage battery is rated in ampere- hours…

A: Given that Charge storage capacity of battery is Q = 100 A-hr = (100 A )X ( 3600 s) = 360000 C…

Q: The four 60 W bulbs each are connected in series swift a battery across them, which of the following…

A: When bulbs are connected in series current through them is same.

Q: When a car's starter is in use, it draws a large current. The car's lights draw much less current.…

A: Terminal potential difference of battery V = E - Ir E = emf of cell r = internal resistance of…

Q: A 60-W light bulb is in a socket supplied with 120 V. What is the current in the bulb? A. 0.50 A D.…

A: Given data : Power=P Voltage=V To find : Current in bulb

Q: What is the rate of the flashlight’s energy consumption, in watts, if it operates at a voltage of…

A: Rate of energy consumption is called Power. Power of flash light can be given as: P=VI Current…

Q: A light bulb is rated at 30 W when operated at 120 V. How much charge enters (and leaves) the light…

A: Write a given values of this question. P=30WV=120Voltt=1min=1×60=60sec

Q: 10) (5 pts) Four bulbs have ratings of 70 W, 80 W, 90 W, and 110 W. Which bulb has the highest…

A: Power = V2 /R given power are 70W 80 W 90W and 110W

Q: A light bulb is rated at 300 W when operated at 120 V. How much charge in C enters (and leaves) the…

Q: A light bulb is rated at 30 W when operated at 120 V. How much charge enters (and leaves) the light…

A: Here given the light operated at 30 W at 120 V. We have to calculate the amount of charges that…

Q: An 18.0 W device has 9.00 V across it. How much charge goes through the device in 4.00 h?

Q: A light bulb is rated at 300 W when operated at 120 V. How much charge in C enters (and leaves) the…

A: Given: The rating of the bulb is 300 W. The potential difference is 120 V. The time interval is 1…

Q: 24. An electric circuit is consisted of a 8 ohm resistor and a 4 ohm resistor connected in series…

Q: A battery has a terminal voltage of 13.5 V when no current flows. Its internal resistance is 2.00 Ω.…

Q: 75-W light bulb draws a current of 0.80 A. If the light bulb stays on for 3 hours, how much charge…

Q: ric pow 3. A battery-powered global positioning system (GPS) receiver operating on 9.0 v draws a…

A: Given data as per question voltage = 9v current = 0.13 time = 2h

Q: An unknown resistor is connected between the terminals of a 9.00 V battery. Energy is dissipated in…

Q: The current flowing through a resistor is measured at several differnet voltages. What is the value…

Q: Giant electric eels can deliver a voltage shock of 5.00 x 102 V and up to 1.00 A of current for a…

A: Hi, you have posted multiple questions without specifying which question to be solved so we will…

Q: 24. An electric circuit is consisted of a 8 ohm resistor and a 4 ohm resistor connected in series…

A: Given: Voltage V=24 V Resistance R8=8 Ω Resistance R4=4 Ω

Q: 21 If 5.0x10 electrons pass through a 20- 0 resistor in 10 min, what is the potential difference…

A: No. of electrons passed is N = 5×10²¹ Resistance is R = 20 Ω Time taken by electrons to pass is t…

Q: An unknown resistor uses 22 W when connected to a 12-volt battery. When connected to a 36- volt…

A: Given,

Concept explainers

Ohm's law

Ohm’s law is a prominent concept in physics and electronics. It gives the relation between the current and the voltage. It is used to analyze and construct electrical circuits. Ohm's law states that the voltage across a conductor is directly proportional to the current flowing through it.

Path of Least Resistance

In a series of alternate pathways, the direction of least resistance is the actual or metaphorical route that offers the least resistance to forwarding motion by a given individual or body.

Question

A light bulb is rated at 30 W when
operated at 120 V. How much charge
enters (and leaves) the light bulb in
9.4 min?
Select one:
a. 169.20
O b. 141.00
O c. 84.60
d. 103.40
O e. 112.80

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
If electrical energy costs 0.12 per kilowatt-hour, how much does it cost to (a) burn a 100-W lightbulb for 24 h? (b) Operate an electric oven for 5.0 h if it carries a current of 20.0 A at 220 V?
A car battery with a 12-V emf and an internal resistance of 0.050 is being charged with a current of 60 A. Note that in this process the battery is being charged. (a) What is the potential difference across its terminals? (b) At what rate is thermal energy being dissipated in the battery? (c) At what rate is electric energy being converted to chemical energy? (d) What are the answers to (a) and (b) when the battery is used to supply 60 A to the starter motor?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
Unreasonable Results (a) What current is needed to transmit 1.00 102 MW of power at 10.0kV? (b) Find the resistance of 1.00 km of wire that would cause a 0.0100% power loss. (c) What is the diameter of a 1.00-km-long copper wire having this resistance? (d) What is unreasonable about these results? (e) Which assumptions are unreasonable, or which premises are inconsistent?
In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
A typical cell phone consumes an average of about 1.00 W of electrical power and operates on 3.80 V. (a) What average current does the phone draw from its battery? (b) Calculate the energy stored in a fully charged battery if the phone requires charging after 5.00 hours of use.
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
Lightbulb A is marked 25.0 W 120. V, and lightbulb B is marked 100. W 120. V. These labels mean that each lightbulb has its respective power delivered to it when it is connected to a constant 120.-V source. (a) Find the resistance of each lightbulb. (b) During what time interval does 1.00 C pass into lightbulb A? (c) Is this charge different upon its exit versus its entry into the lightbulb? Explain. (d) In what time interval does 1.00 J pass into lightbulb A? (e) By what mechanisms does this energy enter and exit the lightbulb? Explain. (f) Find the cost of running lightbulb A continuously for 30.0 days, assuming the electric company sells its product at 0.110 per kWh.