A linear resistance potentiometer is 50 mm long and is uniformly wound with wire having a resistance of 10000 ohm. Under normal conditions, the slider is at the centre of the potentiometer. Find the linear displacement when the resistance of the potentiometer as measured by a Wheatstone bridge for two cases is (1) 3520 ohm (2) 8250 ohm .

A linear resistance potentiometer is 50 mm long and is uniformly wound with wire having a resistance of 10000 ohm. Under normal conditions, the slider is at the centre of the potentiometer. Find the linear displacement when the resistance of the potentiometer as measured by a Wheatstone bridge for two cases is (1) 3520 ohm (2) 8250 ohm .

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
Consider the circuit below. Point b is grounded(potential=0). Determine the potential at a. Two resistors of cylindrical shape, A & B, made from the same material. The length of resistor A is twice that of resistor B. The diameter of B is half that of A. Determine the ratio of Resistance of A/Resistance of B.
"What is the initial resistance of a material in ohm, given: 23 ohms as the final resistance, 250C and 480C as the initial and final temperature and 0.00456/0C as the temperature coefficient of resistance of the material at 480C?"
A potcntiometer with a uniform resistance per unit length of track is to ,I have a track length of 100 mm and used with the output being measured '] with an instniment of resistance 10 k ohm. Determine the resistance required of the potentiometer if the maximum error is not to exceed 1 % ofthe full-scale reading.
What are the applications of clamper circuits? Enumerate 3. Provide references.
4 One of the methods of charging materials wherein the transfer of charges is due to the contact between two materials and depends also on the nature of the materials. Select one: a. charging by friction b. charging by conduction c. charging by induction d. charging by grounding
Commercially available strain gages, typically, have nominal resistance of either 120 or 350 Ohm. Discuss the advantages and disadvantages of each type in terms of measurement accuracy/precision and sensitivity.
I need helpo with this. I need step by step solutions for this and I cant figure it out. Wire to be used in buildings and homes in the United States is standardized according to the AWGsystem (American Wire Gauge). Wires are assigned a gauge number according to their diameter.The scale ranges from gauge 0000 to gauge 36 in 39 steps. The equation for the wire gauge interms of the wire diameter in millimeters is the picture. (a) What is the equation for the diameter in millimeters in terms of the wire gauge N?(b) You have two wires, one that has five times the diameter of the other. By how much do thewire gauges differ for the two wires? (Give your answer to the nearest integer.)
A wire of 59 in length and 4 mm2 has a resistance of 0.94 ohms. A 110-m length of wire of the same material has a resistance of 3 at the same temperature. Find the radius of this wire. The final unit must be in millimeter, mm.
Cyclic Voltammetry and Charge-discharge The given figure is the Galvanostatic Charge-discharge curves of a supercapacitor made with MnO2 coated on a CNT electrode. Potential is measured with respect to time by applying different current densities. Based on the plot, answer the following questions 4. Is it possible to estimate maximum power of the device with this charge-discharge curve? If possible, explain how you would do it. (calculation is not necessary)
a) Mention few factors how variation of resistance is possible in practice. Compute the resistance of a 10m carbon wire with cross section area of 100 mm² (note: Carbon resistivity (p) is 3.5 x 10-5ohm-m, and R= pL/A). b).What do we call the special cases when resistance is 0 ohm, and when resistance is infinite?
A PMMC instrument gives 25mA at full scale reading when a potential difference across its terminals is 75mV. Show that how it can be used (a) as an ammeter for the current measurement in the range of 0-100A (b) as a 0 - 750V range voltmeter for the voltage measurement. Also, find the multiplying factor of shunt and voltage amplification.