A load of 25 KN is to be supported by three 20KN equidistant vertical rods as shown. At first, all the bars are balanced to share the load equally. Dismissing any chance of buckling, determine the final stresses when an additional load of 20 KN is added. Use Esteel = 205 Gpa, Ecopper = 100 Gpa. %3D Steel Copper Sleel

A load of 25 KN is to be supported by three 20KN equidistant vertical rods as shown. At first, all the bars are balanced to share the load equally. Dismissing any chance of buckling, determine the final stresses when an additional load of 20 KN is added. Use Esteel = 205 Gpa, Ecopper = 100 Gpa. %3D Steel Copper Sleel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A prismatic bar with a length L = 3ft and cross- sectional area A= 8in2 is compressed by an axial centroidal load P= 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W=35", and show the stresses on a properly oriented stress element.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4350 mm2 and an allowable normal stress of 130 MPa. Bar (2) has a cross-sectional area of A2 = 4550 mm2 and an allowable normal stress of 80 MPa. Assume x1 = 2.2 m, x2 = 2.9 m, y1 = 1.3 m, and y2 = 2.6 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
A steel bar AD has a cross sectional area of 300mm^2 and loaded by a force P1=15kN, P2=10kN, and P3=8kN. The lengths of the segments are a=2.0m, b=0.6m, and c=0.90m. E=200GPa. a. Determine the change in length of the bar. b. determine the stress of member BC. c. By what amount should the load P3 be incresed so that the bar does not change in length when the three loads are applied?
Three equidistant vertical rods, each of 20 mm diameter, support a load of 25 kN in the same plane as shown in Fig.1 Initially, all the rods are adjusted to share the load equally. Neglecting any chance of buckling, and taking Esteel= 205 GPa and Ecopper 100 GPa, determine the initial and final stresses when a further load of 20 kN is added.
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the tensile stress is 140MPa.
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
A mild steel rod of 15mm diameter that is 1.5.m in length is elongated by 0.15cm along its longitudinal direction by a load of 15 kN. The intensity of stress is?
b.The strong room of a school where an exam question papers are kept is made up ofrectangular metal bars.One bar has a width of 10 mmand would beable to withstand a maximum compressive stress of 20 MPa. i.Prove that,the minimum breadth of thisbar can withstand a burdened with a force of 3 KN. ii.If the bar in question is 2 mlong and decreases in length by 0.25 mmwhen aforce isapplied, then show thata percentage strain can be obtained. iii.What would be its Modulus of Elasticity, E?
Three steel rods (E5 29 3 106 psi) support an 8.5-kip load P. Each of the rods AB and CD has a 0.32-in2 cross-sectional area and rod EF has a 1-in2 cross-sectional area. Neglecting the deformation of bar BED, determine (a) the change in length of rod EF, (b) the stress in each rod.