A load of W = 1400 1b hangs from member AC as shown. Member AC is constrained by a ball-and-socket joint at C and two cables, AE and BD. Calculate the tensions in the cables and the components of the reaction force at C. Use the given coordinate system.

Q: A statistical significant result is A a result that is unlikely due to chance B. a result that is im...

A: Option A is correct

Q: 4-1. If A, B, and D are given vectors, prove the distributive law for the vector cross product, i.e....

A:

Q: Q-2) Find K in the rotational system to yield a 30% overshoot and a settling time of 3 seconds for a...

A: Time=3sec30% overshoot To-Find:- K   where T1=Torque on gear1 T2=Torque on gear 2

Q: Find the general term of the sequence, starting with n = 1. Determine whether the sequence converges...

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure....

A:

Q: An air-standard Carnot cycle operates in a piston-cylinder device between temperatures of 300 and 90...

A: GivenCarnot cycleT1=T2=Tmin=300KT3=T4=Tmax=900KP1=Pmin=0.10MPaQrej=60kJ/kg

Q: h h (а) (b)

A:

Q: A cylindrical tank having radius R is half filled with water having density p. There is a hole at th...

A:

Q: The piece of wood shown below was used in an experiment. During the test it sheared parallel to the ...

A: The formula for calculating average shear stress is force per unit area, using this formula the aver...

Q: For the frame shown, determine the minimum bolt diameter at B if the shear stress in the bolt is 13....

A:

Q: Cars A and B are traveling in adjacent highway lanes and at t = 0s have the position and velocity sh...

A:

Q: Figure 1. The boiler has an inside diameter of 1800 mm and a wall thickness of 20 mm, and it is made...

A:

Q: Determine the force in member AE of the loaded truss. The force is positive if in tension, negative ...

A:

Q: Calculate the amount if work which a ball bearing of weight 50mN does against the drag force (fluid ...

A:   Given: weight of the ball bearing→W=mg=50mN=50×106N distance travelled by the ball bearing→d=1mete...

Q: 2. What is the present value o

A: Need to find present value.

Q: A contractor buries a 6-inch diameter ductile iron water pipe in frozen ground at a depth of 4-feet ...

A: THERMAL CONDUCTIVITY Thermal conductivity is the property  of material which shows the  capability o...

Q: 9. The distance between two inaccessible points A and B on a level ground is to be determined. A thi...

A: Given:AC=300 mBC=520 m∠ACB=99°

Q: The L bar is supported by a universal gasket at O and by the two wires as shown. The universal joint...

A: Draw the free-body diagram of the beam.  

Q: Essay about familiarization on machine

A: Machine familiarization is nothing but giving the required knowledge or information about the featur...

Q: Cars A and B are traveling in adjacent highway lanes and at t= 0s have the position and velocity sho...

A: Calculated relative velocity of car B with respect to car A at the moment car A overtake car B.

Q: n. Find the discharge in pipe in L

A: Applying  Bernoulli's Eq: 60 = V2 / 2g V= (60 * 2 * 9.81)1/2 = 34.31 m/sec Q = V * A = 34.31 * 3.14 ...

Q: If 100 fr of atmosphere air at zero Fahrenheit temperature are compressed to a volume of 1 ft at a t...

A:

Q: Ew =w, + ſkc.s.P(7 aš)– Ic.s.F d$ + W Eletric + WM IIIa.3.2 IIIa.3.10 CV. Magnetic +... C.S. e =u+ p...

A: Given:  To obtain:  

Q: You want to save an amount of 100000 at the end of 10 years. you are given 8% interest compounded qu...

A:

Q: Discuss challenges you encounter in using Vernier caliper. Would you prefer digital caliper over ma...

A:

Q: Các giá trị: • L=700mm • F=130N • a = 60° B = 50° a F1

A: Given we have  F1=40NReferring from figure  we have Fx→=(-F2 Sin 50°)iN=(-40 Sin 50°)i N=-30.641 iNF...

Q: B A bracket shown in the figure is designed to carry a dead weight of W = 15000 N. What sizes of fil...

A:

Q: 2. Use the METHOD OF SECTIONS to determine the forces in members CE, DE, and DF of the truss in Figu...

A:

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 8 kN and M =...

A: Given data: L=8 kNM=52 kNL= 5 m Need to determine the magnitude of the vertical reaction at point D.

Q: A beam is subjected to equal 12.1 kip-ft bending moments. Assume t1 = t2= tw=2 in., d = 12 in., b1 =...

A:

Q: A two-blade wind turbine is installed on top of a hill experiencing winds of up to 80 mile/h. Downst...

A: Given data: Upstream velocity = 80 mi/hr =vu = 35.7632 m/s Downstream velocity = 50 mi/hr = vd = 50 ...

Q: A 10- ft tank contains gas at a pressure of 500 psia, temperature of 85 °F and a weight of 25 pounds...

A:

Q: Consider the masses A and B with weight as shown. If the two systems are released from rest, which b...

A:

Q: m long pipe. The Tank has a constant: s an inside diameter of 15 cm. At ste. n of oil. While the inl...

A: law of concentration of mass qin = Adhdt +qoutqin = Adhdt+πd2v4............1  v = velocity of flow t...

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 1...

A: Option - B => 0.0241 mm => Total Deformation on the brass

Q: a) Consider the crank-slider mechanism in Figure Q3.a. The symbols r and s stand for the length of t...

A: Calculated the distance of OB of the slider from O.  And calculated linear velocity of point B on th...

Q: If the P-value for a one-tailed test is 0.019, then the null hypothesis would be rejected or not rej...

A: In the null hypothesis, the value of p is determined form the statistical tests which describes how ...

Q: Your family just bought a very small cabin in Estes Park, CO, and they have asked you to help figure...

A: GIVEN: Temp to be achieved = 23° C The internal gains = 600 W The Heat transfer of the whole buildin...

Q: 2) The temperature distribution in the square chimney is to be analyzed by the finite difference met...

A: Given : To find : Temperature at the nodes

Q: 4) If the block has mass of 60 kg and its initial velocity is 1.1 m/s (at x = 3 m), determine the no...

A:

Q: Given F1=155 N, F2=187 N Determine the z component of the moment of reaction at the fixed wall A (in...

A:

Q: quations for the circumferential and lo

A:

Q: A box is projected up an inclined plane with velocity of 5 m/s as shown in Fig. (2). Determine: (a) ...

A:

Q: 68. Water at a rate of 1 m'/s enters a small hydraulic turbine from the horizontal supply line, havi...

A:

Q: y-coordinates of tne centrolId of the shaded area. y R d0 R R, 0 3 ỹ = R sin 0 do

A:

Q: Q2/ An object of mass 15 kg is moving with a uniform velocity of 4 ms. What is the kinetic energy po...

A: Givenmass of the object m=15kgvelocity V=4m/s

Q: water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir height=...

A: RESERVOIR A repository  is most generally an augmented regular or fake lake made utilizing a dam to ...

Q: The beam is supported by a Pin at A and a short link BC. If P = 15 kN, determine the average shear s...

A:

Q: ソーH 12 ft

A: As per given question  Length of column=12 ft Stress=50 ksi We have to determine the largest axial l...

Q: Determine the force in truss members BC and EC and indicate whether they are in tension or compressi...

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.