REFERENCE: FROM BOOK - ENGINEERING THERMOFLUIDS, M. MASSOUD 64. Oil (v = 1E–4 m³/s), enters an open tank at a steady rate of 2 m/min andleaves through a 25 m long pipe. The Tank has a constant cross sectional area of 3m and the pipe has an inside diameter of 15 cm. At steady state conditions, theexit pressure is 2 m of oil. While the inlet flow remains constant, we increase theexit pressure instantaneously to 3 m of oil. Find the effect on oil level and exitflow rate.

law of concentration of mass qin = Adhdt +qoutqin = Adhdt+πd2v4............1 v = velocity of flow…

Answered: m long pipe. The Tank has a constant: s…

Engineering

Mechanical Engineering

m long pipe. The Tank has a constant: s an inside diameter of 15 cm. At ste. n of oil. While the inlet flow remains o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. Air flows isentropically through the channel To = 300 ° C. both ends have an identical area that is A = 25 cm², pressure p1 = 120 kPa and p2 = 60 kPa. Determine : a). Mass flow rate, b). Throat area C). Ma2
Air flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)
Show complete solution: Prove that for a fluid with a constant density ρ flowing at a steady-state through a straight pipe with an entry diameter of D1 and an exit diameter of D2 where D1 > D2, the difference of the velocities, i.e. v1 – v2 (velocity in – velocity out), has a negative value. Suppose that for the same system, the ratio of the velocities v1/v2 = 1/4, what is the relationship between D1 and D2?
Water at 940 kPakPa , 25∘C∘C enters a 1-mm-diameter horizontal pipe with a steady velocity of 19 m/sm/s . At the exit the pressure drops to 860 kPakPa due to viscous resistance. Assuming steady-state flow, determine the rate of heat transfer (Q˙Q˙) necessary to maintain a constant specific internal energy (uu).
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanks
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!
The volumetric flowrate of CCl4 (? = 0.659 g/cm3) in a pipe is 5.39 L/s. Find:a.the mass flow rate of the CCl4,b.the molar flow rate of the CCl4, andc.if it enters and exits to an irregular pipe with the inlet and outlet pipe diameters are 2.00 in and 8.00 in, respectively, the exit velocity.
1) Interpret solar power in the context of environmental impact.2. What is the rigid dichotomy between windmill and diesel-driven pumps?3. For a normal windmill-driven pump at 3 m/s wind speed, the yield at a 10 m Head is typically 0.12 liters/s per m2 of rotor area, value windmills in the context of yield.
C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline. The diameter at the smaller end is 245 mm and at the larger end is 467 mm. The length of the conical tube is 1.8 m and the flow rate of the oil is 128 liters/s. The pressure at the smaller end is equivalent to a head of 9.7 m of oil. Considering the following two cases: (1) Neglecting friction, (without head loss) determine (i) the velocity at the smaller end in m/s, (ii) the velocity at the larger end in m/s, and (iii) the pressure at the larger end of the tube. (2) If a head loss (with head loss) in the tube is hL= 0.0153(V1-V2)2, where V1 is the velocity at the smaller end and V2 is the velocity at the larger end, determine (iv) the head loss in m of oil and (v) the pressure at the larger end of the tube.
It is required to construct a hydraulic turbine (inward Francis type) for a hydraulic power plant to operate under the following conditions: rotating speed N = 110 rpm, discharge Q = 11 m3/s, the radial velocity at the inlet Cr1 = 2 m/s, the radial velocity at exit Cr2 = 9.5 m/s and the physical data are: the outside diameter D1 = 4.5 m, the absolute inlet angle α1 = 15°, the absolute exit angle α2 = 90° (radial flow at exit). Assume that the potential energy is constant (Z1 = Z2), the pressure head at exit equal 6 m, the hydraulic losses are 2 m, and no draft tube. Calculate the following:The pressure head at entrance in kg/cm2It is required to construct a prototype to predict the actual machine performance, the assumed outside diameter D2 of the prototype was 0.3 m and the hydraulic circuit in the laboratory has the following specification: Available head = 5.5 m, Hydraulic efficiency = 0.8. Find the required speed, in RPM: The Head subjected on the turbine in meters.The…
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.