A load P is applied to a steel rod supported as shown by an aluminum plate into which a 0.6 in.-diameter hole has been drilled. Knowing that the shearing stress must not exceed 18 ksi in the steel rod and 10 ksi in the aluminum plate, determine the largest load P that can be applied to the rod. 1.6 in.- 0.4 in. 0.25 in. 0.6 in.

A load P is applied to a steel rod supported as shown by an aluminum plate into which a 0.6 in.-diameter hole has been drilled. Knowing that the shearing stress must not exceed 18 ksi in the steel rod and 10 ksi in the aluminum plate, determine the largest load P that can be applied to the rod. 1.6 in.- 0.4 in. 0.25 in. 0.6 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
The beam is to be cut lengthwise along both sides, as shown in the figure. Nap made of a material that has an allowable shear stress of tperm = 75 MPa, determine the shear force maximum allowable V that can be applied before and after making the cut.
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft in MPa. ( COMPLETE SOLUTION NO ROUNDING OFF)
A hollow shaft has an inner diameter of 0.035m and an outer diameter of 0.06m. compute the torque if the shear stress is not to exceed 120MPa.
Beam ABC with an overhang BC is subjectedto a linearly varying distributed load on spanAB with peak intensity q0 = 2500 N/m and a pointload P = 1250 N applied at C. The beam has a widthb =100 mm and depth h = 200 mm. Find the state ofplane stress at point D located 150 mm below the top ofthe beam and 0.2 m to the left of point B. Also find theprincipal stresses at D. Neglect the weight of the beam.
Solve using method of consistent deformation; EI =4x10^6 KN m^2, L=3.0, Wo=20KN/m
A spiral riveted pen stack 1.5-m in diameter is made of steel plate 10-mm thick. The pitch of the spiral or helix is 3-m. The spiral seam is a single riveted lap jointconsisting of 20-mm diameter rivets. Using a shear stress of 70 MPa and bearing stress of 140 MPa, determine the spacing of the rivets along the seam for a water pressure of 1.25 MPa. Neglecting the end thrust, what is the circumferential stress.
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at top of the beam section at 3.09 from the support. (MPa) Properties: Beam width = 259 mmBeam height = 447 mmPu = 63.85 kNSpan of the beam = 10 mPrestressing force = 502 kNeccentricity = 96 mm
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
A hollow vertical cylindrical steel pipe with an outside diameter of 300 mm and 6 mm thick has a length of 3 m. The pipe is fixed at the bottom and free on top and is subjected to a torque of 25 Kn-m and lateral force 39 kN. G = 78 GPa. Calculate the maximum angle of twist in degrees, maximum shear stress due to torque, maximum shear stress due to lateral force, and maximum flexural stress.