A steel column of hollow circular cross section shown in Figure 2 is supported on a circular steel base plate and a concrete pedestal The column has outside diameter 220 mm and a wall thickness of 15 mm. It supports an axial load of 680 kN. a. Determine the bearing stress induced by the column to the base plate in MPa. b. If the allowable bearing stress on the pedestal is 10MPa, determine the required diameter of the base plate in mm.

Q: Q.2) Complete these lines by choosing the suitable compounds words from the brackets (housework,…

A: Note : As per the guidelines for multiple questions only one question can be answered for other…

Q: the bottom of the beam and at asectionofthebeam 0.57 m from the pin if P = 412.2 D

A:

Q: m. Assume atmospheric pressure of 101.3 kN/m2 For the siphon shown in figure below, the maximum…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: 11.2 (A) (a) Derive the formula for strain energy resulting from bending of a beam (neglecting…

A: a) Consider the following free body diagram:

Q: Using Cantilever Method, find the reactions at A, B and C. All sections have the same cross…

A:

Q: rimary and secondary) per day. Assume 30% removal efficiency of the primary clarifier and F/M ratio…

A: Given:- The plant processes 7000 m3/d of wastewater 180 mg/L of BOD5 150 mg/L of suspended solids.…

Q: 1. A reinforced-concrete rectangular beam has a width of 300mm and effective depth of 400mm. Design…

A: fc = 21.1 MPa fy = 345 MPa

Q: Briefly describe why we ignore the concrete below the primary tensile reinforcement in terms of…

A: In cracked section theory, we assume that there is no any concrete mass and entire tensile stress is…

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the value of strain Change in length of rod=D0.02 mm Initial length of rod=1000 mm

A:

Q: A ground profile consists of 9.0 meters thick sand soil. Water table is located 4.0 meters below…

A:

Q: omplete the table and determine the following: Find the difference in elevation of Station 1 and…

A: Height of instrument method BM 12 elevation = 208.65m HI = Elevation + BS Elevation = HI - FS

Q: The rigid AB beam shown in the figure is supported by elastic rods 1 and 2 at points A and B.…

A:

Q: Determine the angle measured clockwise from the major principal axis to the x axis of the section,…

A:

Q: Critical path, Total float, Free float, Independent float A- 3 B 4 C 3 . DA 2 EB 6 FC 4 GD,E 7 HF,G…

A:

Q: A boy is playing on a playground ride as shown below. The bo is holding onto a rope as the platform…

A: Draw the FBD of the boy showing all forces including the outward centrifugal force. Then using…

Q: What is wrong about the modulus of toughness? O a. It is calculated based on the stress strain…

A: Modulus of toughness- It may be defined as the total strain energy per unit volume which can be…

Q: A tacheometer was setup at station P and observations were taken on a staff held at Q and R.…

A: Given data,

Q: Using Cantilever Method, find the reactions at A, B and C. All sections have the same cross…

A: Solution: Given:

Q: 2. The simple beam is subjected to loadings: w= 100 kN/m, F= 500 kN, M= 5000 kN-m. The lengths are:…

A:

Q: A simple beam 4.4 m in span carries a concentrated load of 283 kN at its midspan and is subjected to…

A: fy = 248 N/mm2 (or 248MPa) P = 283 KN l = 4.4m M (max moment) = PL/4 = 283x4.4/4 = 311.3 KNm =…

Q: gr. 0.88 enters the cylind A, at 0.16 N/s. The 80-m dy flow, determine the a

A: Discharge at A :Q=0.16NsγQ=0.160.99×9810=1.853×10-5m3s

Q: For the overhanging beam shown, compute the deflection at the right end if P = 1060lb , W =…

A:

Q: Calculate cost of premium. Rating of Area: 1 Class: A Building: $90,000 Contents: $30,000

A:

Q: illustration and complete solution. A 6° simple curve has an angle of intersection of the tangents…

A:

Q: Determine the shear value (kN) when x = 1.4m from the left side of the beam where: L = 4.2 m; Wo =…

A:

Q: A steel section has the following properties: A = 0.012 m^2 rt = 0.053m tf = 0.016m Sx =…

A:

Q: Determine the maximum positive moment (lbs-ft) in the simply supported beam as shown. Where: L1 =…

A:

Q: 5. The drive shaft for a truck having a diameter of 50 mm is running at 2500 rpm. If the shaft…

A:

Q: FIGURE Q2 shows the scenario that happened during the earthwork stage of the construction project.…

A: It’s a Slope Failure  Resons of slope failure  Slope failure occurs when the driving forces overcome…

Q: kwL For the cantilever beam AB as shown in figure, slope at free end is EI The value of constant k…

A:

Q: Estimate the constant rate of withdrawal from a 1375 hectare reservoir in a month of 30 days during…

A:

Q: A ground profile consists of 2.0 meters silty sand underlain by 3.0 meters of clay. The ground water…

A:

Q: 6. Determine the number of pounds and kilograms of rebar required for a construction project with…

A: ASKED: To determine the pounds and kilograms of rebar for given bar list. Given, 700 No. 6 - 20 ft…

Q: 4.10 A solid cylinder of length H, diameter D and of relative density S floats in neutral…

A: S = 0.6   To find out the ratio of H to D.

Q: An extruded beam has the cross section shown. Determine the location e of the shear center O. 5 mm C…

A: From the given data: a = 30mm b= 45mm t1 = 4mm t2 = 5mm d = 70mm

Q: For the load group and influence line shown, P₁ = 8 kips, P2 = 32 kips, P3 = 32 kips, a = 14', and b…

A:

Q: Problem #2 B 60° A H Weight = X KN E 6. 5. What is the force in cable AH? (kN) What is the force in…

A:

Q: A double angle tension member L5 x 3 x 1/4, is connected to a gusset plate with 7/8 inch diameter…

A: Answer Double angel 2L 5 x 3 x 14 Bolt diameter = 7/8 in Fy = 248.8 Mpa Fu = 400 Mpa Service Live…

Q: lined upward 30° from the horizontal, 3-m wall at a horizontal distance of 18

A: In x-direction ax=0uxt+12axt2=sxucos30×t=18

Q: the force in members DF, EF, and EG of the Howe root truss te whether each member is in tension or…

A:

Q: 1. The breaking point year is 2. The corrected slope of double mass curve is 3. The original slope…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: A ground profile consists of 9 meters thick sand soil. Water table is located 4 meters below ground…

A: Given  Porosity = n = 0.379  G = 2.66  Water table at 4m below the ground surface

Q: 1. For the given singly reinforced beam section, fy =352 MPa, and f's = 28MPA. Calculate the…

A:

Q: Assume that A 8 24' the station of the PI is 64 + 27.46 and terrain conditions require the minimum…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: 11.7 (A/B). A solid shaft carrying a flywheel of mass 100 kg and radius of gyration 0.4m rotates at…

A:

Q: concrete rectangular beam has a width of 300mm and effective depth of 400 weight of beam anymore…

A:

Q: B. Shear and Moment Diagram Instruction: Determine the Maximum Shear and Maximum Moment of the…

A:

Q: An ascending gradient of 1 in 100 meets a descending gradient of 1 in 120. A summit curve is to be…

A: Given data, Design speed = 100 kmph Stopping sight distance=220 m to find the length of summit…

Q: Solve the reactions for the frame and draw the shear & moment diagram for each member. Calculate the…

A: Given: Determinate frame Shear and moment diargarm are to be drawn