A load with a weight of 125.0Newtons is attached to a brass wire with a length of 7.5 meters. Young's modulus of elasticity of the metal wire is 8.96 X 10^11 Pascals. What is the change in length of the brass wire if the radius of its cross sectional area is 0.7 mm. A 5.80 X 10^-4 6.80 X 10^-4 4.80 X 10^-4 3.80 X 10^-4 B D

A load with a weight of 125.0Newtons is attached to a brass wire with a length of 7.5 meters. Young's modulus of elasticity of the metal wire is 8.96 X 10^11 Pascals. What is the change in length of the brass wire if the radius of its cross sectional area is 0.7 mm. A 5.80 X 10^-4 6.80 X 10^-4 4.80 X 10^-4 3.80 X 10^-4 B D

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 47PQ

See similar textbooks

Similar questions

The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
Review. On a day that the temperature is 20.0C, a concrete walk is poured in such a way that the ends of the walk are unable to move. Take Youngs modulus for concrete to be 7.00 109 N/m2 and the compressive strength to be 2.00 109 N/m2. (a) What is the stress in the cement on a hot day of 50.0C? (b) Does the concrete fracture?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
Bone has a Youngs modulus of 18 109 Pa. Under compression, it can will island a stress or about 160 106 Pa before breaking. Assume that a femur (thigh bone) is 0.50 m long, and calculate the amount of compression this bone can withstand before breaking.
Calculate the pressure due to the ocean at the bottom of the Marianas Trench near the Philippines, given its depth is 11.0 km and assuming the density of sea water is constant all the way down. (b) Calculate the percent decrease in volume of sea water due to such a pressure, assuming its bulk modulus is the same as water and is constant. (c) What would be the percent increase in its density? Is the assumption of constant density valid? Will the actual pressure be greater or smaller than that calculated under this assumption?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
A high-speed lifting mechanism supports an 800.-kg object with a steel cable that is 25.0 m long and 4.00 cm2 in cross-sectional area. (a) Determine the elongation of the cable. (b) By what additional amount does the cable increase in length if the object is accelerated upward at a rate of 3.0 m/s2? (c) What is the greatest mass that can be accelerated upward at 3.0 m/s2 if the stress in the fable is not to exceed the elastic limit of the cable, which is 2.2 108 Pa?
During heavy lifting, a disk between spinal vertebrae is subjected to a 5000-N compressional force. (a) What pressure is created, assuming that the disk has a uniform circular cross section 2.00 cm in radius? (b) What deformation is produced if the disk is 0.800 cm thick and has a Young's modulus of 1.5109N/m2 ?