A long foundation 0.6 m wide carries a line load of 100 kN/m. Calculate the vertical stress, at a point P, the coordinates of which are x = 2.75 m, and z = 1.5 m, where the x coordinate is normal to the line load from the central line of the footing

A long foundation 0.6 m wide carries a line load of 100 kN/m. Calculate the vertical stress, at a point P, the coordinates of which are x = 2.75 m, and z = 1.5 m, where the x coordinate is normal to the line load from the central line of the footing

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 9.15P

See similar textbooks

Related questions

Q: 25.0 m 5.0 m 15.0 m 6.0 m. 15.0 m

A: Given: Uniform contact pressure of 120 kN/m2 Width of foundation = 15m To Find: A) Determine…

Q: 7. A shallow square foundation with the dimension of 2.5m by 2.5m is constructed at a depth of 1.5m…

Q: Question Attached

A: Gross bearing pressure: Gross bearing pressure is a total pressure at the base of the foundation due…

Q: A concentrated load of 45000 Ib acts at foundation level at a depth of 6.56 ft below ground surface.…

A: Solution; Given that; Q=45000 lb r=16.4 ft z=32.8 ft

Q: Refer to Figure 5,determine th eaverage stress increase in the clay layer below the center of the…

A: Solution; ∆σav(H2/H1)=4qoH2Ia(H2)-H1Ia(H1)H2-H1B'=α' =0.5β =0.5*1.5 =0.75 m

Q: A rectangular foundation 4 m x 6 m (Figure 1) transmits a stress of 100 kPa on the surface of a soil…

A: The stress is 100 kPa. The load is calculated as, Q=Stress×Area=1006×4=2400 kN The expression for…

Q: Problem (4.10): The foundation plan shown in the figure below is subjected to a uniform contact…

A: Consider the free body diagram , total loading can be divided into equal parts using the line (z-z);

Q: Three foundations are located next to each other (Figure 3). Determine the stress increases at A, B,…

Q: The concentrically loaded square foundation with dimensions of 2.0mx 2.0m, shown in the given…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: 23. Three foundations are located next to each other as shown in Figure 3. Determine creases at A,…

A: Given:- d=2m To find:- stress increase at A,B and C

Q: Solve Problem 6.8 using Eqs. (6.14) and (6.29).

A: Consider the given figure.

Q: m 3 m-2.5 m-- -6 m- 5 ml 4, = 120 kPa 5 m q1 4, = 90 kPa 3 m 5m q3 5m 4" 100 kPa 4 m -4 m- E

A: Draw FBD: Calculating stress using formula:

Q: A square foundation 5 × 5mis to carry a load of 4 MN. Calculate the vertical stress increase at a…

A: According to Newmark's method, Newmark gave a chart according to which we can determine the vertical…

Q: A continuous foundation is shown in Figure 6.24. If the load eccentricity is 0.2 m, determine the…

A: Solution; Given that; e=0.2 m B=2 m, D.F=1.5 m

Q: Determine the increase in vertical stress at a depth of 2m in the soil below point A due to the…

Q: Figure Q1 shows two parallel strip footings 3m wide and 5m apart (measured from centre to centre),…

A: Given: The width of the footing is 3 m. The distance between footings is 5 m. The compressive…

Q: principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane and 50 kPa…

Q: rectangular footing 6 m x 3 m carries a uniform pressure of 300 kN/m² on the surface of a soil mass.…

Q: Estimate the (See figure below). The foundation exerts a uniform vertical stress of 120 kPa at…

Q: n the following example, a rectangular foundation must be designed whose B/L ratio must be equal to…

A: step 1-

Q: n the following exercise, the load capacity (Qu) per meter of length must be calculated for a…

A: step 1-

Q: Problem 2. The centroid of a strip foundation whose width, B, is 5.0 m is located 10 m away from the…

A: The centroid of the foundation is 10 m from a vertical cut edge. Foundation width is 5 m. Vertical…

Q: A rectangular foundation was designed for an allowable bearing capacity of 3,500 psf. Calculate the…

A: Given data, Allowable bearing capacity = 3500 psf To find out the stress increase at point A.

Q: Question attached

A: Solution: Given Data: Square footing=1.5m×1mDf=1 mFOS=4Gross Allowable Load=? Gross Ultimate Bearing…

Q: A square footing foundation, 3 m by 3 m, and positioned on the ground surface of a soil deposit,…

A: (a) The expression for the surface load is given by, Here, q is the surface load, Q is the load…

Q: Q1.1// The figure below shows the plan of a rectangular raft foundation which supports a total load…

A: Given: The total load is 40500 kN. The depth is 8 m. The x and y coordinates are (-9, -6.5).

Q: The site for a commercial building project has the surface elevation lowered 2 m to improve area…

A: where, r = distance from axis z = depth

Q: If a rectangular foundation of dimension 2.5 m by 3.5 supporting a load of 900 kN is supported at a…

A: Given foundation of dimension 2.5 m by 3.5 supporting a load of 900 kN depth of 1.5 m below the…

Q: Refer to Figure P5.5. Using the procedure outlined in Section 5.5, determine the average stress…

A: The formula to calculate the total stress increase caused by a rectangularly loaded area for any…

Q: - A 1.2 m wide long (strip) footing carries a wall loading of 36 kN per meter of wall length. What…

A: Given:-L=1.2 m = 1200mmLoad= 36kN/mdepths = 1m,2m,4mTo find:-vertical stress results according…

Q: ¹:50, 100, and 150 kN point loads are applied at Points A. B, and C. respectively. on the ground…

A: Given data in question Loads Dimensions Depth To find out Vertical stress increament at point D…

Q: (b) Figure Q2 (b) shows the ring foundation to support a silo. Given R1 = 3 m while R2 = 6 m. The…

A: Given data: R1= 3 mR2=6 m Depth 7 m with a interval of 1m.

Q: A square footing is loaded as shown in Figure 05.13. The center of the base of footing is at…

Q: Refer to Figure 5.2. A square foundation measuring 1.5 m x 1.5 m is supported by a saturated clay…

A: Given DF=1 m Cu=115 kN/m2 width of footing,B=1.5 m γsoil =18.5kN/m3 since the soil is undrained…

Q: Determine the increase in vertical stress at a depth of 5 m below the centroid of the foundation…

A: Consider the given figure.

Q: Problem (4.10): The foundation plan shown in the figure below is subjected to a uniform contact…

A: Uniform contact pressure= 40kN/m2 As the shape of the foundation is not mentioned let us assume the…

Q: A rectangular foundation (8x6 ft) carrying an axial load of 350 Kips is constructed on the soil…

A: Given :

Q: ELABORATE Try solving the following problem: Practice Problem: A rigid foundation is subjected to a…

A: P = 550KN L = 3m B = 2m Df= 1.5m H = 5m Es= 13500knN/m2 μs = 0.5 It has been asked in the question…

Q: A column foundation [ 2.0 m x (1.7m] in size is located at a depth of 1.4 m in a strong cohesive…

A: The following figure shows the sketch of the foundation. Given Data: Length of foundation is L=2 m.…

Q: It has been determined that the stress increase occurring at a depth of 6 m below the center of the…

Q: For a shallow foundation shown below: Estimate the ultimate bearing capacity when the water table…

A: Answer We are given Width of Foundation B = 2m Length of Foundation L = 3m Depth of Foundation Df =…

Q: The initial principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane…

Q: Determine the vertical stress at point A (use influence factors) at the depth of 8m and point B (use…

A: The values and diagrams given in the question are as follows: Uniformly distributed load(q)=250 kPa…

Q: A foundation of 1.0 m in radius with a thickness of 300 mm is located at a depth of 1.5 m below the…

Q: A foundation (Figure 1) transmits a stress of 100 kPa on the surface of a soil deposit. a. Evaluate…

A: Radial distsnce of A = 0Radial distance of B rB=22+32=3.6 mRadial distance of C rC=42+12=4.12…

Q: The plan of a rectangular foundation shown in figure transmits a uniform contact pressure of 120…

A: We have to determine the value of vertical stress induced by the loading of 120 KN/m2 at point B…

Q: A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the…

Q: The initial principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane…

A: Option (a) is the correct answer. Draw the Mohr's circle before & after construction. The…

Question

Q.8 A long foundation 0.6 m wide carries a line load of 100 kN/m. Calculate the vertical stress, at a point P, the coordinates of which are x = 2.75 m, and z = 1.5 m, where the x coordinate is normal to the line load from the central line of the footing

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider a continuous foundation of width B = 1.4 m on a sand deposit with c = 0, = 38, and = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 6.33). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination = 18. Estimate the failure load Qu(ei) per unit length of the foundation a. for a partially compensated type of loading [Eq. (6.89)] b. for a reinforced type of loading [Eq. (6.90)]
A long foundation 0.6 m wide carries a line load of 100 kN/m. Calculate the vertical stress σz, at a point P, the coordinates of which are x = 2.75 m, and z = 1.5 m, where the x-coordinate is normal to the line load from the central line of the footing.
Refer to Figure 5.2. A square foundation measuring 1.5 m x 1.5 m is supported by a saturated clay layer of limited depth underlain by a rock layer. Given that Df = 1 m, H = 0.7 m, cu = 115 kN/m2, and γ = 18.5 kN/m3, estimate the ultimate bearing capacity of the foundation.
In the following exercise, the load capacity (Qu) per meter of length must be calculated for a continuous foundation that has an eccentricity e=1.2m in the width direction of the foundation.
A square foundation of (5m x 5m) is to carry a load of 4000KN.calculate the vertical stress at a depth of 5m below the center of the foundation. IN=0.084 for m=n=0.50 Also, determine the vertical stress using the 1:2 distribution method.
The shallow foundation shown in Figure 4.24 measures 1.5 m x 2.25 m and is subjected to a centric load and a moment. If eB = 0.12 m, eL = 0.36 m, and the depth of the foundation is 0.8 m, determine the allowable load the foundation can carry. Use a factor of safety of 4. For the soil, we are told that unit weight γ = 17 kN/m3, friction angle Φ' = 35°, and cohesion c' = 0.
Consider a continuous foundation of width B = 1.4 m on a sand deposit with c' = 0, Φ' = 38° and γ = 17.5 kN/m3. The foundation is subjected to an eccentrically inclined load (see Figure 4.31). Given: load eccentricity e = 0.15 m, Df = 1 m, and load inclination β = 18°. Estimate the failure load Qu(ei) per unit length of the foundation a. for a partially compensated type of loading [Eq. (4.85)] b. for a reinforced type of loading [Eq. (4.86)]
A rectangular footing 6 x 3 m carries a uniform pressure of 300 kN/m 2 on the surface of a soil mass. Determine the vertical stress at a depth of 4.5 m below the surface on the center line 1.0 m inside the long edge of the foundation?
A 6 m. x 9 m. rectangular foundation carrying a uniform load of 288 kPa is applied to the ground surface. Compute the total vertical stress in kPa due to this uniform load at a depth of 6 m. below the center of the loaded area if unit weight of soil is 18,30 kN/m.
The shallow foundation shown in Figure 6.25 measures 1.5 m × 2.25 m and is subjected to a centric load and a moment. If eB = 0.12 m, eL = 0.36 m, and the depth of the foundation is 0.8 m, determine the allowable load the foundation can carry. Use a factor of safety of 4. For the soil, we are told that unit weight γ = 17 kN/m3, friction angle ф′ = 35°, and cohesion c′ = 0.
A square footing foundation, 3 m by 3 m, and positioned on the ground surface of a soil deposit, supports a column load of 1,350 kN. Determine the vertical stress resulting from the foundation loading at a depth 3 m below the base of the footing for locations beneath the center and beneath the edge, assuming:(a) Boussinesq conditions apply.(b) Westergaard conditions apply.
A rectangular footing 6 x 3 m carries a uniform pressure of 300 kN/m2 on the surface of a soil mass. Determine the vertical stress at a depth of 4.5 m below the surface on the center line 1.0 m inside the long edge of the foundation.