A long shunt compound Generator supplies 10 kW at a terminal voltage of 200 V. The machine parameters are as follows: R = 0.07 , R, = 0.1, R₁ = 120 2. If the total losses percentage are 20% and the torque developed by the prime mover is 119.4 N.m, find the following after drawing the circuit diagram: 1. Overall efficiency and the input power 2. Copper loss, 2. Iron and friction loss, 4. Speed in r.p.m.

A long shunt compound Generator supplies 10 kW at a terminal voltage of 200 V. The machine parameters are as follows: R = 0.07 , R, = 0.1, R₁ = 120 2. If the total losses percentage are 20% and the torque developed by the prime mover is 119.4 N.m, find the following after drawing the circuit diagram: 1. Overall efficiency and the input power 2. Copper loss, 2. Iron and friction loss, 4. Speed in r.p.m.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 50-kW generator has a full-load efficiency of 90.5 percent. Determine the total losses. Ans.: 5,250 watts explain step by step, circuit diagram, principles etc and also write it clearly.
Q20) A 1000rpm DC shunt generator is supplying 100 lamps of 60W at 230V, the armature and field resistance are respectively 0.1Ω and 115Ω.Calculate the generated emf. a. 232.809 V b. 222.809 V c. 212.809 V d. 242.809 V
Q3/ A 50 Hz three-phase induction has 8 poles, the rotor speed is 742.5 rpm. The Power supplied to a motor is 25 KW and the Stator Losses are 0.75 KW. Find the: (a) Synchronous speed and slip (b) Rotor Copper Loss, (c) Total Mechanical Power Developed by the Rotor, (d) Output Power of the Motor if Friction and Windage Losses are 0.5 KW, (e) Efficiency of the Motor, neglecting Rotor Iron Losses
10. A short shunt compound dc generator supplies 7.5 kW at 230 V. the shunt field, series field and armature resistance are 100, 0.3 and 0.4 ohms respectively. Calculate the induced emf. a. 253.8 V b. 255.7 V c. 259.6 V d. 257.1 V
A 6-phase ∆-connected 1600 V (line-to-line), 150 kW, 50 Hz, six-pole induction drive is used in an electric car. The drive has the following parameter values in Ω/phase referred to the stator: R1 =0.334 Ω R2 =0.168 Ω Rm1 = 125 Ω X1 = 0.273 Ω X2 = 0.287 Ω Xm1 = 16.78 Ω The total friction, windage, and core losses may be assumed to be constant at Prot =773 W, independent of load. For a slip value of s=0.015: a) Draw the equivalent circuitb) Compute the speed, output torque, power and stator currentc)Determine the power factor and whether leading or lagging d)Calculate the efficiency when the motor is operated at rated voltage and frequency.
A Four pole, 50kW, 250 Volt Long Shunt DC Machine Generator has a shunt field current of 1.5 A. It is Lap-winded with 872 conductors, and a rated speed of 1200 RPM. Ra= 0.1 Ohms, and Rse = 0.05 Ohms. Solve for the following: Mechanical, Electrical, and Commercial Efficiency when the Stray Loss is 1600 W Total Copper Loss
No. 8 problem A shunt generator has the following open-circuit characteristic at 800 r.p.m. Field amperes : 0.5 1.0 1.5 2.0 2.5 3.0 3.5E.M.F. Volt : 54 107 152 185 210 230 245 Armature and shunt field resistances are respectively 0.1 Ω and 80 Ω. The terminal p.d. falls to 175 V when the armature current is 100 A. Find the O.C. volts and the volts lost due to (i) reduction in the field current(ii) armature resistance (iii) armature reaction.
The following figures give the O.C.C. of d.c. Shunt generator driven at a constant speed of 700r.p.m.Terminal voltage (V): 10 20 40 80 120 160 200 240 260Field Current (A) : 0 0.1 0.24 0.5 0.77 1.2 1.92 3.43 5.2Determine the critical resistance at (a) 700 r.p.m. (b) 850 r.p.m. If resistance of field coils is 50 Ω, findthe range of the field rheostat required to vary the voltage between the limits of 180 V and 250 V on opencircuit at a speed of 700 r.p.m.
A self-excited DC shunt generator is delivering20 A to a 100-V line when it is driven at 200 rad/s.The magnetization characteristic is shown inFigure. It is known that Ra = 1.0 Ω andRf = 100Ω . When the generator is disconnectedfrom the line, the drive motor speeds up to 220 rad/s.What is the terminal voltage?
A shunt generator delivers 195 A at terminal p.m. of 250 V. The armature resistance and shunt field resistance are 0.02 ohm and 50 ohm respectively. The iron and friction losses equal 950 W. Find (a) E.M.F. generated (b) Cu losses (c) output of the prime mover (d) commercial, mechanical and electrical efficiencies.
A 460 V, 25 Hp, 60 Hz, 4-pole, Wye-connected rotor has the following omega/phase impedances referred to the stator circuit. R1=0.641 ohms, X1=1.106 ohms, R2=0.332 ohms, X2=0.464 ohms, Xm=26.3 ohms. A) Torque max, ans Smax and wm at which T max occurs? B) Start of torque C) If R2 is doubled, at what speed is maximum torque produced?, D) Plot the original torque-speed curves and the adjusted T (with R2 doubled)
A 440 V, single-phase synchronous motor is taking 50 A at a pf of 0.9 lagging. The effective resistance of armature is 0.8 Ω. If the iron and friction losses amount to 600 W, find the horsepower output.