A long-shunt compound generator supplies 22 kW at a terminal voltage of 220 V. The resistance of the armature, the shunt field and the series field are respectively 0.05 ohm, 110 ohms and 0.06 ohm. If the overall efficiency of the above load is 88%, find iron a friction losses.

A long-shunt compound generator supplies 22 kW at a terminal voltage of 220 V. The resistance of the armature, the shunt field and the series field are respectively 0.05 ohm, 110 ohms and 0.06 ohm. If the overall efficiency of the above load is 88%, find iron a friction losses.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Related questions

Q: 3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2=…

A: for a delta connected induction motor,v1=440 Vpole: p=6fs=60 hzGiven parameters:R1=0.048 ΩR2=0.035…

Q: A dynamic system is represented by the following equation: 4X(t) + 8 x(t) + 16 x(t) = sin(51) The…

A: 2nd order Differential equation is given We need to find natural frequency by applying Laplace…

Q: Consider the moving average filter with length N = 21. For each of the following input signals f[k],…

A: Please post the remaining subparts in another question. Given data, Length N=21 To find:- a) fk=3 b)…

Q: i. Find the resulting values of IcQ and VCEQ. j. Find ß at the operating point. 1, If for con on R…

Q: Two long parallel conductors carry 200 A. If the conductors are separated by 40 mm, the force per…

A: Given, current in both conductors, I1=I2=200 A The separation between the conductors,d=40×10-3 m

Q: In a 500/250 volt 3-wire d.c. system, there is an out of balance load of 200 kW on the positive…

Q: 2. Analog to Digital Using PCM, perform the steps need to convert the signal to its digital…

A: Given: To find: From the graph of analog to digital conversion, we have to answer, i) How many…

Q: 7. Calculate the output voltage expression for the circuit

Q: 8.39 Consider the magnetic circuit in Figure 8.39. Assuming that the core (μ = 1000μ¸) has a uniform…

Q: Given the following system, determine the response of the system, the roots of the system, the…

A: Given: A system having transfer function=16s2+4s+16, To find: a) Response of the system, b) Roots of…

Q: In reference to the given circuit, what is the dc load voltage, Blank 1 if the diode drop is 0.65V?…

A: Given: Primary RMS Voltage = 110Vrms The primary transformer turns N1 = 10 The secondary transformer…

Q: Problem 4 Given is one period of DTFT function X(w) and Y(w) for |w| ST lal s elsewhere between-","…

A: Given data Xω=1 for ω≤π32 Xω=0, elsewhere, between -π, π and, Yω=1 for π2-π64ω≤π2+π64 Yω=0,…

Q: A 60 Hz synchronous generator having inertia constant H = 6 MJ/MVA and a direct axis transient…

Q: 2. Simplify the following expressions: cost (a) +) 5 (t) (b) 2t² +1 jw-3 w²+9 *5(w) (Hint: * means…

A: Given expression- a cost2t2+1 δtb jω-3ω2+9*δω To find- Simplified expression

Q: 1. An accelarated aging-test is to be performed on a bushing with a capacitance of 1250 pF by…

Q: Consider the signal ≤ n ≤2 y (n) = {0, elsewhere a) Compute the DTFT of the signal i.e. Y(w). Find…

A: Given: y(n)=1 ;0≤n≤20 ;otherwise To find: a) DTFT of the signal. Sketch the magnitude and phase…

Q: In the circuit of Fig. 9.54, determine the value of is (t). 115 cos 2,000t V is (t) 2Ω ww + 2 mH m…

Q: Find v₁ (t) and v₂ (t). ↑ 302 3.5 cos(15t +594 12 cos(15t -30°) V (+-) 0.15H

Q: 8.6 Given that B = 6xa, 6xa, - 9ya, + 3za. Wb/m², find the total force experienced by the rec-…

Q: Q/1/ Single phase half-wave uncontrolled rectifier. The battery charger circuit that is used to…

A: Given, The supply voltage, Vs=250 V The supply frequency, fs=50 Hz

Q: 1. A potential divider of a resistance of 50 ohms is connected across a 100 V DC source. A load…

Q: Find i(t) and z(t). 10 sin(30r +90) V F 722 2raF 9.SH

Q: Given a 20μC point charge at P(2,1,4), a line charge 30μC/m along the y-axis, and a surface charge…

A: Given, Point charge, Q = 20μC at P(2,1,4) a line charge, pl = 30μC/m along the y-axis,surface…

Q: Given a truth table in Table Q2, determine the standard SOP expression. Simplify the expression and…

A: We need to find out the Boolean expression for given truth table .

Q: * The voltage Vout in the circuit shown is

A: Given data, Circuit diagram is given as,

Q: 8) For the following circuit: a) Find the voltage across the inductor b) Find the Real Power,…

Q: Find poles and zeros of the system having the following transfer function G(s) then show the poles…

A: We need to find out the pole and zero for given system and we need to check stability of given…

Q: The output current i(t) at t<0 is equal to zero Amperes. Determine the following: a. an expression…

A: Parallel RC circuit A parallel RC circuit consists of a resistor and a capacitor connected in…

Q: j) Is there a change in the underlying DTFT of the signal y(n) when you add zero-padding? k) What…

A: Given: y(n)=1 ;0≤n≤20 ;elsewhere, To find: j) Is there any change in the DTFT of the signal y(n)…

Q: 1. The switch in the circuit below has been open for a long time. At t=0 the switch is closed. a)…

Q: 1) Using Thevenin's Theorem to determine the current flowing in the R5 resistor. The voltage has…

Q: 1. Determine the appropriate value of frequency for a square wave generator (in Hz) to measure the…

A: In this question, We need to determine the frequency of the Series RC circuit to measure the time…

Q: • Short time constant (delay time, dead times) T.: 1 ms System gain Ks: 7 • Proportional-action…

Q: On no-load, a shunt motor takes 5 A at 250 V, the resistances of the field and armature circuits are…

A: The current is 5 A The voltage is 250 VThe resistance is 250 ohm and ohm in field and armature…

Q: Consider the unity feedback system shown in Figure 2 where R(s) is reference input and Y(s) is…

A: Given, The unity feedback system,

Q: A DC DC motor should be operated a strong field which is due to the What happens to suddenly goes a)…

A: motor operating in strong field due to current if suddenly if = 0 what happens to rotating motor

Q: a. Consider the following energy band diagram for the junction and determine the built-in potential…

A: given here a energy band diagram and asked to find the built-in potential.

Q: U₂ U3 U₁ O U

A: We need to find out the voltage for given circuit.

Q: find RL and max power transfer to RL

A: It is given that:

Q: A chopper feeding on RL load is shown in the figure, with V= 200 V. R=50 L= 5 mH f = 1 kHz, d = 0.5…

Q: Write state space equation for the following system when the I represents the output of the system

Q: .A thermal couple measures a temperature range between 0°C to 500°C. It is required that the…

A: Given data, Temperature, T1=0T2=500 °C Temperature change ∆T=0.5 °C

Q: III. Find the current Lby reducing the circuit to the right of terminals a-b to its simplest form…

A: Given: In this question, the given details are, Here, to find the value of the current i by reducing…

Q: Compute for the average and rms values of the voltage v(t) = 440 cos (2513t 195⁰) V.

A: In this question We need to determine the average value of voltage and rms value. This is…

Q: -4. A 30 KW, 250-V, d.c. shunt generator has armature and field resistances of 0.060 and 100…

Q: expression and draw the logic circuit. the standar 001 010 011 100 Table Q2 INPUTS ABC 000 OUTPUT X…

A: Given,

Q: Find the real and reactive power absorbed by each element in the following circuit. -j5 n HE + VE…

Q: A loadline is drawn on the BJT transistor characteristics shown in Figure 3. f. Determine the value…

Q: Question In a single-phase transformer, the total iron loss is 2500 W at nominal voltage of 440 V ar…

A: In this question We need to determine the hysteresis losses and eddy current losses at nominal…

Q: Consider the DT signal x[n] shown in the plot below. You can assume that x[n] = 0 for all values of…

Concept explainers

Synchronous Motor

The synchronous motor is an AC electric type motor where at a steady-state the shaft rotation is synchronized with the supply current variable-frequency. To an integral number of AC cycles, the rotation period is exactly equal. The stator of the motor in the synchronous motor contains multi-phase AC electromagnets due to which a magnetic field is created that rotates in time with the oscillation of the line current. The rotor contains a permanent magnet and the rotor rotates in synchronization with the stator field at the same rate and provides the second synchronized magnetic field which is rotating in nature as a result. When the synchronous motor is supplied with independently excited multi-phase AC electromagnets on both the rotor and the stator, it is termed as a doubly-fed machine. The most widely used AC-type motors are the synchronous AC motor and the induction AC motors.

Question

A long-shunt compound generator supplies 22 kW at a
terminal voltage of 220 V. The resistance of the
armature, the shunt field and the series field are
respectively 0.05 ohm, 110 ohms and 0.06 ohm. If the
overall efficiency of the above load is 88%, find iron a
friction losses.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
A single-phase alternator connected to 6,600-V bus-bars has a synchronous impedance of 10Ω and a resistance of 1 Ω. If its excitation is such that on open circuit the p.d. would be 5000 V, calculate the maximum load the machine can supply to the external circuit before dropping out of step and the corresponding armature current and p.f. [2864 kW, 787 A, 0.551]
A 3 phase, wye-connected salient-pole generator has on per phase basis Xd = 2 ohms, Xq = 1.5 ohms and R∅ = 0. When delivering its maximum power output to an infinite bus bar, the terminal and excitation voltages/phase are 1,430 V and 1,495 V, respectively. Find the power angle in electrical degrees at the above conditions
A Y-connected, 3-phase, 1732 V, 120 kVA, synchronous generator has a synchronous reactance of 1.2 Ω/ph???. Feeds the specified load with pf = 0.9(+) . Fixed losses are assumed to be 5% of developed power. Find: A. The tension generated. b. The power angle. c. Voltage regulation. d. Efficiency. E. Phasor and Power Flow Diagrams
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
A short-shunt compound generator has armature, shunt field and series field resistances of 0.5 2, 156 R, and 0.465 2 respectively. If it supplies a load of 9 kW at a terminal voltage of 241 V, calculate the generated emf in volt.
15. A certain generator has an open-circuit voltage of 12 V and an internalresistance of 40Ω . Calculate: (a) the load resistance for maximum powertransfer; (b) the corresponding values of the terminal voltage and of thepower supplied to the load.If the load resistance were increased to twice the value for maximum powertransfer, what would be the power absorbed by the load?
A transmission line has a reactance of 1 Pu is operating at Vs = Vr = 1 Pu. The generator is connected at source end which is delivering 0.5 Pu of active power. Find the load angle?
A straight-line law connects terminal voltage and load of a 3-phase star connected alternator delivering current at 0.8 power factor lagging. At no-load, the terminal voltage is 3,500 V and at full-load of 2,280 kW, it is 3,300 V. Calculate the terminal voltage when delivering current to a 3-phase, star-connected load having a resistance of 8 o and a reactance of 6 ohm per phase. Assume constant speed and field excitation.
Q2/ A 50 kW, 200 V differentially compounded generator has NSE of 10 turns, NF of 3000 turns, and RF of 70 Ω. Calculate the value of the magnetomotive force at no-load and full-load operating conditions.
Q2. The O.C.C for a shunt generator at (1000 r.p.m) given by:lf(A) 0.2 0.5 1.0 1.5 2.1 2.4 3 4.2 4.8E(V) 28 72 144 202 245 270 300 345 360The armature resistance equal (0.5 ohm) and shunt field resistance equal (83.33 ohms). If the machine is driven at (1100 r.p.m) find:(a)The load current if the load resistance equal (9 ohms). (b)The number of series winding to convert the machine to level compound at (345 V) at armature .current of (100 A)
*need in 20 mins please :((* A short-shunt compound generator has armature, shunt field and series field resistances of 0.5 Ω, 125 Ω, and 0.321 Ω respectively. If it supplies a load of 8 kW at a terminal voltage of 233 V, calculate the generated emf in volt.