A M16 x 2 hex-head bolt with a nut is usedto clamp together two 25-mm thick steelplates. (e) Determine the tensile stress in the boltdue to tightening it with a 50 N.mtorque. Assume that the bolt iszinc-plated.(f) An external load of 100 kN is appliedon the members after tightening thebolt. What will be the stress in the boltnow? Will there be yielding in the bolt?

GivenM16×2 hex-head boltt=25 mm

Answered: A M16 x 2 hex-head bolt with to clamp…

Engineering

Mechanical Engineering

A M16 x 2 hex-head bolt with to clamp together two 25-mm thick steel plates. a nut is used

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Related questions

Q: 3. A flange compressive coupling is used to connect a driving electric motor to a reduction gear box…

Q: esign of the Screw Jack. Lifting load – W, kN is 70. Hight of lifting– H, mm is 500 Types of…

A: a screw jack is used to transfer the rotational movement into linear movement. It Uses a power screw…

Q: OAK Oes = Voe? + 3. T,² < S Oeş 0010 Calculate the factor of safety when preloading an M20 (6.6)…

Q: - 10. A Metric 16 2 bolt (16-mm diameter, 2-mm pitch) is subjected to rque of 15 N-m during…

Q: Design of the Toggle Jack. Lifting load – W, kN is 8 Distance between nuts– B, mm is 50 - 280…

A: Given: Lifting load is W=8 KN number of links is n=8 length of the link L=140 mm material of the…

Q: Find the number of bolts M8*1 which made from SAE Grade 4 steel that should be used to provide a…

Q: A permanent bolted joint has four M24 ISO 8.8 bolts with coarse threads. The joint stiffness…

A: Answer: 136mm Solution is given below.

Q: A 5000-lb. gear box is provided with a steel (as rolled B1113) eyebolt for use in moving it. What…

A: Given Force, F = 5000 lb Material = Rolled B1113 Find Size of the bolt, D

Q: of screw thread from ihe foll reasons for it. (2) (31

A: Since you have posted a question with multiple sub-parts, we will solve first three sub parts for…

Q: Find the number of bolts M8 1 which made from SAE Grade 4 steel that should be used to provide a…

Q: 3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The…

A: The standard dimension of the nut and bolt are: Washer size:

Q: Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn…

A: Given DataN1=18 teethω1=1200 rpmω2=240 rpmP=10 hp ***As per company policy we are supposed to do…

Q: Statics; Method of joints Solve the following problems with accompanying complete- detailed…

Q: The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade…

Q: A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the…

Q: Figure 3.1 shows that an M10 x 1.5 of class 8.8 steel bolt clamps two metal plates, one aluminium…

Q: State the choice of power screw that suitable to be used for an application under the following…

A: (i) To select: The power screw that suitable to be used for an application under vertical lifting.…

Q: Section A (An Q1(a) Explain types of pin jointed frames with examples.

A: given; explain type of pine joined frames with examples.

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

Q: Bolt properties: M14 x2 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size.

Q: In a single purchase Crab Winch, If number of teeth T1 is greater than T2 then the shaft attached…

A: we know thatVelocity ratio of single purchase crab is given byVR=Dd×T1T2for given condition neglect…

Q: proper key for the joint shown in figure E rque of T= 180 N.m. The hub has length of

A: Given data shaft dia = 30 mm length of hub = 50 mm allowable compressive stress = 120 MPa Required =…

Q: (b) A left-hand threaded rod of nominal diameter 60 mm, pitch 2.5 mm with double start thread of V…

A: Solution:

Q: (12) A turnbuckle connects two rods having %-16 UNC threads. The thread friction is 0.2. How much…

A: Write the given data. μ=0.2P=500 lbdm=0.335 in

Q: A M16 x 2 hex-head bolt with a nut is used to clamp together two 25-mm thick steel plates. (a)…

Q: Which of the following is the permissible working stress in psi of UNC bolts that has a stress area…

A: Given Data: Stress area of the bolt, A=0.4 in2

Q: Find the number of bolts M8*1 which made from SAE Grade 4 steel that should be used to provide a…

Q: Bolt properties: M12 x1.75 ISO 5.8 (a) Determine a suitable length for the bolt, use preferred size.…

Q: A ½ inch nominal major diameter (d = 0.5 [in.]) course series (UNC) bolt is to be used to secure a…

A: The fastener's nominal diameter is its stated measurement from crest to crest. the nominal diameter…

Q: 1- Name the different forms of journal bearings. 2- Sketch with freehand and name the different…

A: Journal Bearings

Q: -.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer…

A: Given data: The diameter of the bolt is D = 24 mm. The length of the bolt is L = 100 mm. Here, the…

Q: Clamping sleeves are placed on shafts on which then friction be arings, toothed gears and simil…

A: Given: Clamping sleeves are placed onshafts on which then friction bebearings, toothed gears, and…

Q: rod. The pitch of the threads is p1.5 mm. Hanger Frame Parallel Knurled nut- springs Threaded rod D…

A: For solution refer below images.

Q: 1. For a bolted assembly with six bolts, the stiffness of each bolt is k» = 3 Mlbf/in and the…

A: Stiffness of each bolt, kb=3Mlbf/in Stiffness of each members, km=12 Mlbf/in per bolt External load,…

Q: : Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer in…

Q: Rolling contact Pin in slot

A: Given:- To Find :- Degree of freedom (DOF)

Q: imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for…

A: Givenbolt specification 34 in coarse- thread SAE grade 8preload for non permanent assembly)From the…

Q: The machine shown in the figure can be used for a tension test but not for a compression test. Why?…

A: Given: There are three gears connected in series and the middle gear is attached to the motor. And…

Q: 16.54 An M12, coarse-pitch, Class-5.8 bolt with a hexagonal nut assembly is used to keep two machine…

Q: A shaft where a hub is mounted has 2 in diameter, transmitting 20 hp power at 750 rpm. Design a…

Q: The figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load…

Q: Determine the number of pin joints 4. Which of the following has multiple degrees of freedom? OOO

Q: What is the complete specification of a nut having a stress area of 0.170 in? (standard size) that…

A: 1/2"-28UNEF-3B-LH

Q: Identify atleast 10 work holding or clamping devices and their use.

A: Chucks Chucks are efficient and accurate devices for holding the work on the lathe during…

Q: For the same question what stiffness k needed so the rod will stop smoothly on horizontal position 3

Concept explainers

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.

Question

A M16 x 2 hex-head bolt with a nut is used
to clamp together two 25-mm thick steel
plates.

(e) Determine the tensile stress in the bolt
due to tightening it with a 50 N.m
torque. Assume that the bolt is
zinc-plated.
(f) An external load of 100 kN is applied
on the members after tightening the
bolt. What will be the stress in the bolt
now? Will there be yielding in the bolt?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a bolted joint two members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
A 1/2-in-dia UNC, class 2 bolt with rolled threads is preloaded to 80% of its proof strength when clamping a 3-in-thick sandwich of solid steel. A static 1000-lb external load is applied. Part A Find the safety factor against static yielding. Express your answer using three significant figures. Part B Find the safety factor against joint separation. Express your answer using three significant figures.
What approximate torque in in-lb is required in tightening a 1” diameter (As=0.606 in2) unlubricated bolt to produce an initial tightening stress of 8141 psi? Round your answer to 4 significant figures
Two 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?
Determine the safe tensile load for fine series bolts of (a) M 24and (b) M 38. Assume that the bolts are not initially stressed and take the safe tensile stress as 450MPa.
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?
Design of the Screw Jack. Lifting load – W, kN is 45. Hight of lifting– H, mm is 450 Types of threads is Square Material of nut is Bronze
Sketch a V-grooved butt joint, and label all of the joint's dimensions.
In using the formula for measuring an American Standard Unified Screw Thread by the three-wire method, why should the constant 0.86603 be multiplied by the pitch before subtracting from measurement M, even if not enclosed by parentheses? E=M+0.86603P+3W ?
Bolt properties: M12 x1.75 ISO 5.8(a) Determine a suitable length for thebolt, use preferred size.(b) Determine the bolt stiffness.(c) Determine the stiffness of themembers.
Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion
For Problem 2.28, ifthe block is placed at the endof thebeam, what should be the length of the steel wire inorder to regain thespacing of 1/16 in between E and B?