A machine component is undergoing a torque load. The part is made up of a 1 m long composite bar. It comprises an inner solid bar of radius 10 mm which is perfectly bonded inside a tube of outer radius 20 mm. If given that the shear moduli of the inner solid bar and outer tube are 48 GPa and 25 GPa respectively, and the composite bar is subjected to a torque of 10 kNm, a) Determine the angle of twist of the composite bar b) Determine the maximum shear stresses in both the inner solid and outer tube

A machine component is undergoing a torque load. The part is made up of a 1 m long composite bar. It comprises an inner solid bar of radius 10 mm which is perfectly bonded inside a tube of outer radius 20 mm. If given that the shear moduli of the inner solid bar and outer tube are 48 GPa and 25 GPa respectively, and the composite bar is subjected to a torque of 10 kNm, a) Determine the angle of twist of the composite bar b) Determine the maximum shear stresses in both the inner solid and outer tube

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing stress is 85 MPa. The pipe CD, which has an outer diameter of 90 mm and a wall thickness of 6 mm, is made of an aluminum for which the allowable shearing stress is 54 MPa. Determine the largest torque T that can be applied at A
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A circular composite shaft is made of a 50-mm-diameter brass (G = 40 GPA) and a 80-mm-outside diameter aluminum (G = 25 GPA) jacket. This shaft is 1.5-m-long and both ends are rigidly mounted so they cannot twist. What is the shear stress at the outer surface of this shaft when a 100 N-m torque is applied at the center?
A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
An 18-mm-diameter solid circular shaft is made of a material that is assumed to be elastoplastic with τY = 145 MPa and G = 77.2 GPa. For a 1.2-m length of the shaft, determine the maximum shearing stress and the angle of twist caused by a 207-N·m torque.
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
A steel shaft of 50 mm diameter and 500 mm length has a total angle of twist of 0.5. If the Modulus of Rigidity is taken as 79 GPa, determine the maximum allowable shear stress that can be induced in the shaft
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.
A flanged bolt coupling consists of ten 15-mm diameter bolts spaced evenly around abolt circle 350 ?? in diameter. Determine the torque capacity of the coupling if theallowable shearing stress in the bolts is 30 MPa.
A flanged bolt coupling has ten (10) steel 25.4 mm diameter boltsevenly tighten around a 415 mm bolt circle. Determine the torquecapacity of the connection if the allowable shearing stress inthe bolt is 50 MN/m2