A mass of flexible machine part, m, of of 10 Hz. The vibration was caused by the application of a harmonic force, F of the flexible part. A judgment was made by a mechanical engineer that the vibration was excessive because the frequency of the harmonic force coincides with the natural frequency of the flexible part. 20 kg was observed to vibrate badly at frequency 100 N to If the flexible machine part is operated in the speed range of 500 to 750 rpm, justify whether the design of vibration absorber in Q3(c) is safe to be used or not. (d)

A mass of flexible machine part, m, of of 10 Hz. The vibration was caused by the application of a harmonic force, F of the flexible part. A judgment was made by a mechanical engineer that the vibration was excessive because the frequency of the harmonic force coincides with the natural frequency of the flexible part. 20 kg was observed to vibrate badly at frequency 100 N to If the flexible machine part is operated in the speed range of 500 to 750 rpm, justify whether the design of vibration absorber in Q3(c) is safe to be used or not. (d)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) Large amplitude of vibration is experienced when an engine having mass (1500 + 2) kg operates at a speed of 1500 rpm. An absorber having stiffness k2equal to 1500 N/m and mass m2 is attached to the primary system to absorb the vibration. Find: The magnitude of the mass of the absorber. The natural frequencies of the system after the addition of the absorber. The values of the stiffness k2 and mass m2 of the absorber in order to have the natural frequencies of the two degrees of freedom system 15% away from the forcing frequency.
A spring of stiffness 2 kN/m is suspended vertically and two equal masses of 4 kg each are attached to the lower end. One of these masses is suddenly removed and the system oscillates. Determine a) The amplitude of vibration, b) the frequency of vibration, and c) the velocity and acceleration of the mass when passing through half amplitude position.
During the design of the spring-support system for the mp=3050 kg weighing platform, it is decided that the frequency of free vertical vibration in the unloaded condition shall not exceed 8.5 cycles per second. a. Determine the maximum acceptable spring constant k for each of the three identical springs. Insert your answer in kN/m correct up to at least a third decimal place. b. For spring constant, what would be the natural frequency fn of vertical vibration of the platform loaded by the mt=60Mg truck? Insert your answer in Hz correct up to at least a third decimal place.
A mass of flexible machine part, ?1 of 10kg was observed to vibrate badly at frequency of 10 Hz. The vibration was caused by the application of a harmonic force, ? of 20 N to the flexible part. A judgment was made by a mechanical engineer that the vibration was excessive because the frequency of the harmonic force coincides with the natural frequency of the flexible part. (a) Interpret the phenomena occurred that explained by the mechanical engineer. If the flexible machine part was be modeled as a spring-mass-damper system, calculate the value of equivalent stiffness, ?1 of the system. Give final answer in unit of kN/m.
3. The 7.5 kg mass shown is vibrating freely with the following spring attached to it. If the required period of vibration is 0.35s, determine (a) the value of the spring stiffness constant R and (b) the vibration response with initial displacement and velocity of 5cm and 24 cm/s, respectively
A motor that turns at 12,000 rpm is suspended from above by a single spring to isolate the building from its vibration. If the natural frequency of the system is to be one fourth of the vibration frequency, by how many centimeters should the spring extend be-yond its unloaded length when the motor is hung on it?
When a 2-kg block is suspended from a spring, the spring is stretched a distance of 40 mm. Determine the frequency of vibration for a O.5-kg block attached to the same spring.
A vibrometer used to measure the amplitude of vibrations consists essentially of a box containing a mass-spring system with a known natural frequency of 120 Hz. The box is rigidly attached to a surface that is moving according to the equation y= δm sin wf t. If the amplitude zm of the motion of the mass relative to the box is used as a measure of the amplitude δm of the vibration of the surface, determine (a) the percent error when the frequency of the vibration is 600 Hz,(b) the frequency at which the error is zero.
Vibration When suspended from a helical spring, a load of 91 kg is found to vibrate vertically with a periodic time of 0.75 s. Determine, for an amplitude of 51 mm : (a) the angular velocity of the generating vector; (b) the maximum acceleration; (c) the acceleration when the displacement is 127 mm; (d) the stiffness of the spring; (e) the static deflection in the spring; (f) the maximum force in the spring (122 N).
A sensitive electronic system, of mass 25 kg, is supported by a spring-damper isolator that rests on the floor of a manufacturing plant. The operation of nearby rotating equipment causes the floor to vibrate with an amplitude of 8 mm at a frequency of 35 Hz. The electronic system can only operate effectively if the amplitude of its acceleration is less than 40 m/s2. It is known that the damping ratio of the isolator is 0.1. i. Determine the maximum stiffness of the isolator needed for the transmitted acceleration level to be acceptable and hence facilitate effective operation of the electronic system. Using the calculated stiffness value, also determine the largest deformation of the spring in millimetres when the system is in motion. ii. If the damping ratio is allowed to increase by only increasing the equivalent damping coefficient (c) of the isolator, discuss the effect this change would have on the response of the electronic system when operating in the same environment. In your…
A collar with mass m that slides on a frictionless horizontal rod is attached to a spring with constant k and is acted upon by a periodic force with a magnitude of P=Pm sin wf t. Determine the range of values of wf for which the amplitude of the vibration exceeds three times the static deflection caused by a constant force with a magnitude ofPm
A machine of mass 75 kg is mounted on springs and is fitted with a dashpot to damp out vibrations. There are three springs each of stiffness 10 N/mm and it is found that the amplitude of vibration diminishes from 38.4 mm to 6.4 mm in two complete oscillations. Assuming that the damping force varies as the velocity, determine : 1. the resistance of the dash-pot at unit velocity ; 2. the ratio of the frequency of the damped vibration to the frequency of the undamped vibration ; and 3. the periodic time of the damped vibration.