A 1 hydrostatic extrusion 2 Strain hardening 3 High temperature 4 Anisotropy in blank metal 5 n=0 6 Friction 7 Indirect Extrusion 8 Barreling 9 Floating plug 10 Blank form 11 Explosive forming 12 Impact load 13 Capstan 14 Bottoming 15 Bar drawing 16 Rolling, extrusion, forging B n reduces Metal flow is retarded Single draft operation Spring Back is reduced Hammers Metal increases its strength at room temperature Very short time forming process. Difficult to support the product when it exit's Open die forging Wire drawing Bulk metal forming Fluid applies force Tube drawing Controls the metal flow under the holder Occurs in Hot forming Earing Answer from A

A 1 hydrostatic extrusion 2 Strain hardening 3 High temperature 4 Anisotropy in blank metal 5 n=0 6 Friction 7 Indirect Extrusion 8 Barreling 9 Floating plug 10 Blank form 11 Explosive forming 12 Impact load 13 Capstan 14 Bottoming 15 Bar drawing 16 Rolling, extrusion, forging B n reduces Metal flow is retarded Single draft operation Spring Back is reduced Hammers Metal increases its strength at room temperature Very short time forming process. Difficult to support the product when it exit's Open die forging Wire drawing Bulk metal forming Fluid applies force Tube drawing Controls the metal flow under the holder Occurs in Hot forming Earing Answer from A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piece with a height of 120 mm and a diameter of 75 mm can be increased to 80 mm in height by pile-forging.is reduced. The coefficient of friction between the workpiece and the mold is 0.13. Flow curve of the workpiece, 165It is defined by a strength coefficient of MPa and a hardening exponent of 0.24. force during operationCalculate at the moments given below and obtain the force-workpiece height graph(1) as soon as it reaches the yield point (yield strain = 0.002),(2) height h = 115 mm,(3) height h = 110 mm,(4) height h = 105mm,(5) height h = 100mm,(6) height h=95mm,(7) height h = 90 mm,(8) height h = 85mm,(9) height h = 80 mm,
A 3in long and 1in diameter billet is extruded in a direct extrusion operation with an rx = 4.0. The extrusion has a cross section. The angle of the die (half angle) is 90o. The work metal has a resistance coefficient of 60ksi and a strain hardening exponent of 0.18. Use Johnston's formula with a = 0.8 and b = 1.5 to estimate the extrusion stress. Determine the pressure applied to the end of the billet when the piston moves forward.
A hot rolling mill has rolls of radius = 105mm. It can exert a maximum force =1219625 Newton. The mill has a maximum horsepower = 91 hp. It is desired to reduce a 25 mm thick plate by the maximum possible draft in one pass. The starting plate is 250 mm wide. In the heated condition, the work material has a strength coefficient = 275 MPa and a strain hardening exponent = zero. Determine(a) maximum possible draft(b) associated true strain(c) maximum rotational speed of the rolls for the operation
Bar stock of initial diameter = 90 mm is drawn with a draft = 15 mm. The draw die has an entrance angle = 18°, and the coefficient of friction at the work‑die interface = 0.08. The metal behaves as a perfectly plastic material with yield stress = 105 MPa. Determine (a) area reduction, (b) draw stress, (c) draw force required for the operation, and (d) power to perform the operation if exit velocity = 1.0 m/min
A flat-rolling operation of 250 mm wide alloy stee Calculate roll torque
What are the limitations of the Use of the Shear Formula?
Where can the complex stress distributions arise?
A direct extrusion operation produces a product with a 20 mm x 60 mm cross sectional area from a brass billet whose diameter = 125 mm and length = 350 mm. The flow curve parameters of the brass are K = 700 MPa and n = 0.35. In the Johnson strain equation, a = 0.7 and b = 1.4. Determine (a) the extrusion ratio, (b) the shape factor, (c) the force required to drive the ram forward during extrusion at the point in the process when the billet length remaining in the container = 300 mm, and (d) the length of the extruded section at the end of the operation if the volume of the butt left in the container is 600,000 mm3
A cylindrical ingot with D0 = 50 mm and h0 = 40 mm is cold forged using an open die.The final height is 20 mm. The coefficient of form / friction between the die and the workpiece isconsider Kf = 1.10.The material from which the ingot is made has the following characteristics:K = 600 MPa and η = 0.12.Determine the force (F) on the operation:a) Force required at the moment of reaching the yield point (ℇ = 0.002)b) Force required when you have a height of h = 30 mmc) Force required when there is a final height of h = 20 mmd) Construct the graphs: Force vs Δh and effort vs Δh
What is the linear variation in the shear strain?
What is the linear variation in shear stress along any radial line?
What is yield stress?