A metal frame is subjected to the couple moments as shown in the figure and parameter table. What is the required distance L₂ that would result in no net couple moment? parameter value units L₁ 2.5 L3 5 1 LA 1.5 4 F₁ 100 F₂ 100 0 60 2.3.5 Ls The required distance is L₂ = ft ft ft ft 16 lb lb . L5 0 F2 X

A metal frame is subjected to the couple moments as shown in the figure and parameter table. What is the required distance L₂ that would result in no net couple moment? parameter value units L₁ 2.5 L3 5 1 LA 1.5 4 F₁ 100 F₂ 100 0 60 2.3.5 Ls The required distance is L₂ = ft ft ft ft 16 lb lb . L5 0 F2 X

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.5.10P: Solve the preceding problem (W 250 × 44.8) if the resultant force P equals 110 kN and E = 200 GPa.

See similar textbooks

Similar questions

(a) Replace force F = -2800i + 1600j + 4000k N acting at end A of the crank handle with a force R acting at O and a couple-vector C. (b) Resolve R into the normal component P (normal to the cross-section of the shaft) and the shear component V (in the plane of the cross-section) (c) Resolve C into the twisting component T and the bending moment M. Please answer C
In the six-bar mechanism in the figure, the joint points are shown with J1, J2,…., J7, and the limb numbers from 1 to 6 as shown in the figure. The limb lengths are as follows: ?1 = 1, ?2 = 0.3, ?3 = 0.7, ?4 = 0.8, ?5 = ?6 = ?8 = ?9 = 0.5, ?7 = 0.7 m A force of F = 1000 N and a moment of magnitude M = 500 Nm is applied to the same limb in the direction shown in the figure, right in the middle of the limb number 6 and perpendicular to the limb and in the direction shown in the figure. In this case, the mechanism is Calculate the moment Mt, which keeps it in balance. İ=6 q2=126 q3=28.10 q4=134.31 q6=97.44 q7=-1.17 q8=74.32 q=angle
A truss is loaded as shown in the Figure. Assume AE = 10,000N. Which of the following most nearly gives the relative displacement between joints B and D id member BD is removed? ( ans. 8.12 mm ) Which of the following most nearly gives the relative displacement between joints B and D due to two-unit loads acting on joints B and D towards each other? ( ans. 1.02 mm ) Which of the following most nearly gives the axial force in member BD? ( ans. 5.61 N )
A 5 m beam is fixed at one end and pinned at other end. It is loaded a couple M at pinned end. If there is one unit rotation at the pinned connected end, EI = 1800 N.m^21. Which of the following gives the value of couple M in N.m at the pinned end? a. 1444b. 4414c. 4441d. 14142. Which of the following gives the value of vertical reaction at pinned end in N? a. 334b. 434c. 443d. 3443. Which of the following gives the value of moment at fixed end in N.m.? a. 334b. 434c. 443d. 344
A steel plate of dimensions 2.5 x 1.5 x 0.08 m and weighing 23.1 kN is hoisted by steel cables with lengths L1 = 3.2 m and L2 = 3.9 m that are each attached to the plate by a clevis and pin (see figure). The pins through the clevises are 18 mm in diameter and are located 2.0 m apart. The orientation angles are measured to be s = 94.4' and a = 54.9° For these conditions, first determine the cable forces T1 and T2, then find the average shear stress Taver in both pin 1 and pin 2, and then the average bearing stress ?? between the steel plate and each pin. Ignore the weight of the cables.
I need help please Two gondolas on a ski lift are locked in the position shown in the figure while repairs are being made elsewhere. The distance between support towers is L = 100 ft. The length of each cable segment under gondola weights WB = 450 lb and WC = 650 lb are DAB = 12 ft, DBC = 70 ft, and DCD = 20 ft. The cable sag at B is Î”B = 3.9 ft and that at C(Î”C) is 7.1 ft. The effective cross-sectional area of the cable is Ae = 0.12 in2.(a) Find the tension force in each cable segment; neglect the mass of the cable.(b) Find the average stress (s) in each cable segment.
The figure shows the combined design of an angular contact ball bearing on two fulcrums. The radial loads R1 and R2 and axial load Fa of bearings 1 and 2 are shown in the figure. The relationship between the derived axial force S and radial load R is: S = 0.25R. Calculate the actual axial force of bearing 1 and bearing 2? Fa= 360N R1=4000N R2=4250N Problem 5) Figure
Please answer the truss problem shown in image the answers are: (i) F1-2 = 58 kN (compression) F1-3 = 58 kN (compression) F2-3 = 29 kN (tension)(ii) R2=R3=50 kN vertically upwards I have also attached my working out as i am not sure where i am going wrong in my calculations.
A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension a=1.9 m and dimension b=2.5 m. The mass of the beam is 85 kg. Use g = 10 N/kg. Hint: Take torques about the hinge and use the perpendicular lever arm version of the torque equation (the sin theta version will work but will require more calculation).
25 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Accordingly, S5 = ? A) 49.5B) 35C) 99D) 70E) 140
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A lifeboat hangs from two ship's davits. as shown in the figure. A pin of diameter d = 0.80 in. passes through each davit and supports two pulleys. are on each side of the davit. Cables attached to the lifeboat pass over the pulleys and wind around winches that raise and lower the lifeboat. The lower parts of the cables are vertical and the upper parts make an angle a =15° with the horizontal. The allowable tensile force in each cable is 1800 lb, and the allowable shear stress in the pins is 4000 psi. If the lifeboat weighs 1500 lb, what is the maximum weight that can be carried in the lifeboat?