A metallic rod rotates about its center at a constant angular speed. If the rod's temperature is increased uniformly, what happens to its speed? A) its speed of rotation increases. B) its speed of rotation decreases. (c) its speed of rotation remains same. D its speed increases because its moment of inertia increases

A metallic rod rotates about its center at a constant angular speed. If the rod's temperature is increased uniformly, what happens to its speed? A) its speed of rotation increases. B) its speed of rotation decreases. (c) its speed of rotation remains same. D its speed increases because its moment of inertia increases

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter16: Temperature And The Kinetic Theory Of Gases

Section: Chapter Questions

Problem 8OQ

See similar textbooks

Similar questions

Consider the piston cylinder apparatus shown in Figure P20.81. The bottom of the cylinder contains 2.00 kg of water at just under 100.0c. The cylinder has a radius of r = 7.50 cm. The piston of mass m = 3.00 kg sits on the surface of the water. An electric heater in the cylinder base transfers energy into the water at a rate of 100 W. Assume the cylinder is much taller than shown in the figure, so we dont need to be concerned about the piston reaching the top of the cylinder. (a) Once the water begins boiling, how fast is the piston rising? Model the steam as an ideal gas. (b) After the water has completely turned to steam and the heater continues to transfer energy to the steam at the same rate, how fast is the piston rising?
A cylinder with a piston holds 0.50 m3 of oxygen at an absolute pressure of 4.0 atm. The piston is pulled outward, increasing the volume of the gas until the pressure drops to 1.0 atm. If the temperature stays constant, what new volume does the gas occupy? (a) 1.0 m3 (b) 1.5 m3 (c) 2.0 m3 (d) 0.12 m3 (e) 2.5 m3
Two cylinders A and B at the same temperature contain the same quantity of the same kind of gas. Cylinder A has three times the volume of cylinder B. What can you conclude about the pressures the gases exert? (a) We can conclude nothing about the pressures. (b) The pressure in A is three times the pressure in B. (c) The pressures must be equal. (d) The pressure in A must be one-third the pressure in B.
Physics A bottle of mass mb = 0.1 kg and volume V = 0.1 m3 is attached to the bottom of a vertical thin rod of length ` = 1 m and mass mr = 2 kg, that is hinged at the top end. The bottle is full of hydrogen (mH = 1.67 × 10−27 kg) and is at atmospheric pressure and temperature T0 = 20 0C. (e) To what height will the rod/bottle system swing up to? (Hint: Don’t forget about the center of mass of the rod.) Angular velocity is 30 rad/sec
The moment of inertia I of a uniform rod rotating around its center point is I = 1/12ml^2 where m is the mass of the rod and l is its length. (A) Derive an expression for the change in the moment of inertia for such a rod, ΔI, that includes the initial moment of inertia I0, the coefficient of linear expansion  for the rod material, and a temperature change ΔT. (B) A uniform rod of mass 0.500 kg and length 1.000 m at T = 0 °C rotates around its center in free fall (e.g., floating in a space station) at an angular velocity of exactly 1 radian per second. If it is warmed to 30 °C and = 20 × 10  −6 °C−1, what would its angular velocity be? Use conservation of angular momentum.
Consider a 55-cm-long journal bearing that is lubricated with oil whose viscosity is 0.1 kg/m?s at 20°C at the beginning of operation and 0.008 kg/m?s at the anticipated steady operating temperature of 80°C. The diameter of the shaft is 8 cm, and the average gap between the shaft and the journal is 0.08 cm. Determine the torque needed to overcome the bearing friction initially and during steady operation when the shaft is rotated at 1500 rpm.
An iron block (c = 0.450 J/gºC) is initially at 60.0 ºC. The block is then submerged into 100.0 g of water (c = 4.18 J/gºC) at 25.0 ºC in an insulated container. The final temperature of the iron block and water upon reaching thermal equilibrium is 26.0 ºC. What is the mass of the iron block?
The brass bar and the aluminum bar in the drawing are each attached to an immovable wall. At 26.6 °C the air gap between the rods is 1.30 x 10-3 m. At what temperature will the gap be closed?
A 10-cm-diameter cylindrical shaft rotates inside a 40-cm-long 10.3-cm diameter bearing. The space between the shaft and the bearing is completely filled with oil whose viscosity at anticipated operating temperature is 0.300 N?s/m2. Determine the power required to overcome friction when the shaft rotates at a speed of (a) 600 rpm and (b) 1200 rpm.
The density of a fixed amount of gas is greatest at: A. SATP B. STP C. 1 bar and 0 degree Celsius D. 1 atm and 25 degree Celsius
Two bicycle tires are set rolling with the same initial speed of 4.0 m/sm/s along a long, straight road, and the distance each travels before its speed is reduced by half is measured. One tire is inflated to a pressure of 40 psipsi and goes a distance of 17.2 mm ; the other is at 105 psipsi and goes a distance of 92.9 mm . Assume that the net horizontal force is due to rolling friction only and take the free-fall acceleration to be ggg = 9.8 m/s2m/s2 . What is the coefficient of rolling friction μrμrmu_r for the tire under low pressure?
Two bicycle tires are set rolling with the same initial speed of 4.0 m/sm/s along a long, straight road, and the distance each travels before its speed is reduced by half is measured. One tire is inflated to a pressure of 40 psipsi and goes a distance of 17.2 mm ; the other is at 105 psipsi and goes a distance of 92.9 mm . Assume that the net horizontal force is due to rolling friction only and take the free-fall acceleration to be gg = 9.8 m/s2m/s2 . What is the coefficient of rolling friction μrμr for the second tire (the one inflated to 105 psipsi)?