A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?

A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in diameter, and six 10 mm diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts?
A 220 mm diameter of 14.5 degrees involute gear is used to transmit 50 kW at 580 rpm Find the total force transmitted on the gear.
Bearing stress 5. Please provide proper discussion and illustration also complete solution and clear solution please thank you A solid shaft is designed to transmit 50kN @ 1800 rpm to a gear by means of 156 mm long key with square cross-section. The shaft diameter is 35.6mm. What should the cross-section be in mm2 to resist shearing, if the allowable shear stress on the key is 20 MPa?
The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
A 1000 mm cast iron pulley is fastened to a 112 mm shaft by means of a 28 mm square key 160 mm long. The key and shaft are SAE 1030 steel annealed with allowable shearing of key at 200 MPa and compressive of 660 MPa. a. What force in lbs is required to shear the key? b. What force in kgs is needed to compress the key? c. Safe power in hp of the shaft at 600 rpm. d. What force in lbs acting at the pulley rim will shear the key? e. What force in lbs acting at the pulley rim will crush the key?
A solid titanium alloy [G=114⁢ GPa] shaft that is 950 mm long will be subjected to a pure torque of T=195 N⋅m. Determine the minimum diameter required if the shear stress must not exceed 145 MPa and the angle of twist must not exceed 3°. Report both the maximum shear stress τ and the angle of twist φ at this minimum diameter. Based only on the requirement that the shear stress must not exceed 145 MPa, what is the minimum diameter of the shaft? dτ= mm Based only on the requirement that the angle of twist must not exceed 3°, what is the minimum diameter of the shaft? dφ= mm Determine the minimum diameter required. dmin= mm Determine the polar moment of inertia corresponding to the minimum diameter for the shaft. J= mm4 Determine the maximum shear stress at the minimum diameter. τmax= t MPa Determine the angle of twist in the shaft at the minimum diameter. Enter your answer in degrees. φ= °
Please solve with clear explanation. Q.solid aluminium shaft 1 m long and 50 mm diameter is to be replaced by a tubular steel shaft of the same length and same outside diameter such that each of the two shafts could have the same angle of twist per unit torsional moment over the total length. What must be the inner diameter of the tubular shaft? Modulus of rigidity of steel is three times that of aluminium.
A motor provides 60 hp power to a wheel B. It rotates a solid shaft in AISI 1020 steel, 4 cm in diameter, at a speed of 300 rpm. Power is drawn from the shaft using belts attached to pulleys A and C. (Use the table if necessary) (a) Draw the torque diagram of the driven shaft. (b) What is the safety factor of the driven shaft? Answer: 5.22 (c) Determine the angle of torsion of pulley C with respect to pulley A. Answer: -1.88°
please show a proper solution thank u! A hollowed circular shaft that can transfer a 20 kN-m torque has the characteristics 72mm for the outside diameter and 40mm for the inside. What is the shaft's least minimum produced torsional shearing stress?
The small gear of an internal gear train shown in the figure is powered by a 500-kW motor at 30 Hz. Whereas this small gear has 10 teeth, the large gear it drives has 30. Hence the large gear rotates at 10 Hz. If the allowable shear stress is 60 MPa, what are required sizes of the shafts?