A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. 400 The shaft is mounted on two bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 B 400 270 250 640 210 640 100

A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. 400 The shaft is mounted on two bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 B 400 270 250 640 210 640 100

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Topic: Thermal & Torsional Stress The four gears are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20 kW are used by gear A, 20 kW by gear C, and 30 kW by gear D. (a) Find the uniform shaft diameter if the shear stress in the shaft is not to exceed 60 MPa. (b) If a uniform shaft diameter of 100 mm is specified, determine the angle by which one end of the shaft lags behind the other end. Use G = 83 GPa for steel.
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
A shaft drives a gear set that is transmitting 8 hp at 2250 rpm. The diameter of the shaft is 1.75 in. Determine the torsional shear stress developed in the shaft.
Design the size of solid steel shaft to be used for a 500 hp, 250rpm application if the allowable torsional deflection is 1o andthe allowable stress is 10,000 psi and modulus of rigidity is 13x 106 psi. Round your answer to the nearest 1/8 inch.
A hollow shaft is to transmit 350 kW at 65 rpm. If the shear stress is not to exceed 40 MPa and the diameter ratio is 0.54, Design the shaft by assuming the maximum torque is 40% greater than its mean torque. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNIT GIVEN IN BRACKET) (i) The mean torque is (Unit is in Nm)=__________ Answer for part 1 (ii) The maximum torque is (Unit is in Nm)=__________ Answer for part 2 (iii) The outer diameter of the shaft (unit in mm)=_______________ Answer for part 3 (iv) The inner diameter of the shaft (unit in mm)=_______________
A 12.6 inches long key is to be used on a 210 hp, 1200 rpm, slip ring induction motor. The key is 1 in wide and has a depth of 3/4 in. The shaft diameter is 3 7/8 inches. The maximum running torque is 200% of the full-load torque. A. Determine the maximum compressive (crushing) stress of the key, in psi. B. Determine the maximum direct shearing stress on the shaft, considering the effect of the keyway, in psi.
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
A pulley is keyed to a 56.8mm diameter shaft by a 7/16 in x 3 in flat key. The shaft rotates at 697 rpm. The allowable compressive stress for the key, hub and shaft are 66 ksi. 59 ksi and 72 ksi, respectively. Determine the maximum torque, in lb-in, the pulley can safety deliver. Express your answer in 3 decimal places.
The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A hollow steel shaft is stressed to 35 MPa by a torque of 200000Nm. Determine the outside diameter in mm if the inside diameter is 2/3 of the outside diameter both in mm.