A moving coil mili voltmeter has a resistance of 20 ohm and full scale deflection of 120 degrees is reaches when the p.d of 100V is applied across it's terminals. The moving coil has effective dimensions of 3.1cm x2.6cm and wound with 120 turns. The flux density in the air gap is 0.15 Weber per meter squared. Determine the control constant of the spring and suitable diameter of copper wire for a coil winding if 55% of the total instrument resistance is due to coil winding given resistivity of 1.73*10-8 ohm meter

A moving coil mili voltmeter has a resistance of 20 ohm and full scale deflection of 120 degrees is reaches when the p.d of 100V is applied across it's terminals. The moving coil has effective dimensions of 3.1cm x2.6cm and wound with 120 turns. The flux density in the air gap is 0.15 Weber per meter squared. Determine the control constant of the spring and suitable diameter of copper wire for a coil winding if 55% of the total instrument resistance is due to coil winding given resistivity of 1.73*10-8 ohm meter

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

For a motor design, you need to design a solenoid coil that produces a magnetic flux density (B) of at least 2000 gauss when a 10 mA current flows through the conductor. Due to space limitations, the coil only can be 10 turns over a 1 cm length. To obtain the needed performance, go to Table 3 and choose a core material for the coil.
A PMMC voltmeter with a resistance of 10 ohms gives has a coil of effective depth of 3 mm and a width of 2.5 cm, the coil has about 100 turns. The flux spread in the air gap is of 10mWb/m2 . The spring has a constant of 2 x 10-6. Then calculate, i. Deflection torque produced by the coil, when it is connected to 20V to measure. ii. Deflection made by the pointer, when the meter is to measure a voltage of 10V. iii. Analyze the reason of fixed the voltage coil in dynamo type wattmeter?
A 200-turn coil is immersed in a 60-Hz flux with an effective value of 4 mWb. Obtain an expression for the instantaneous value of the induced emf. If a voltmeter is connected between its two ends, what will be the reading on the voltmeter?
A PMMC instrument has 100 turns on a former that is 20mm wide, length is 30mm. The flux density in the air gap is 0.002 Tesla. The control spring constant is 0.21x10^-6 Nm/rad. Calculate the current required to produce 120 degree.
The coil of a moving-coil voltmeter is25 mm long and 25 mm wide and has 60 turns on it. The control spring exerts a torque of 1.58 x 10 Nm when the deflection is 100 divisions on full scale. If the flux density of the magnetic field in the air gap is 5 wb/m², estimate the resistance that must be put in series with the coil to give one volt per division. The resistance of the voltmeter coil may be neglected
A permanent-magnet moving coil instrument used as a voltmeter has a coil of 50 turns with a width of 3 cm and active length of 3 cm. The gap flux density is 0.15 Wb/m2. If the full- scale reading is 150 V and the total resistance is 100 kW, find the torque exerted by the springs at full-scale.
A 500-turn coil is wound on an iron core. When a 120-V-rms 60-Hz voltage is applied to the coil, the current is 1 A rms. Neglect the resistance of the coil. Determine the reluctance of the core. Given that the cross-sectional area of the core is 5 cm2 and the length is 20 cm, determine the relative permeability of the core material.
i. 5. A PMMC voltmeter with a resistance of 10 ohms gives has a coil of effective depth of 3 mm and a width of 2.5 cm, the coil has about 100 turns. The flux spread in the air gap is of 10mWb / m. The spring has a constant of 2 x 10^-6 ". Then calculate, i Deflection torque produced by the coil, when it is connected to 20V to measure. Li. Deflection made by the pointer, when the meter is to measure a voltage of 10V.
The two coils A and B wound coaxially on an insulating cylinder. It will be evident that the ﬂuxes produced by a current i through the two coils are in the same direction, and the coils are said to be cumulatively coupled. If the direction of the current in B relative to that in A is reverse, then coils are said to be differential coupling. Suppose A and B to have self-inductances and henrys respectively and a mutual inductance M henrys. If two coils are connected in series, their effective inductance is found to be 12.0H. However, when the connections to one coil are reversed, the effective inductance is 8.0 H. If the coefﬁcient of coupling is 0.6. a) Show that the total inductance of inductively coupled circuits is + ± 2M b) Calculate the self-inductance of each coil and the mutual inductance.
Q23. A PMMC Ammeter has a coil of effective depth of 5 cm and a width of 20 mm, the coil has about 150 turns, and it has coil resistance of 20 ohms. The flux spread in the air gap is done at density of 100mWb / m Then calculate, 1. Control torque produced by the coil, when it measures 15 A. ii. Spring constant, when it measures 15 A and deflects by an angle of 30 ° Deflection torque exerted on the pointer, when it measures 20 A. Analyze the relationship between the area of moving coil and deflection torque produced in a PMMC instrument iv.
. What is the purpose of a discharge device used in conjunction with opening a highly inductive circuit?a) to minimize the possibility of damage to the circuits insulation as a result of a high induced voltage b) to minimize the possibility of endangering the life of the person opening the controlling switch c) to allow the magnetic field to gradually collapse, thus limiting the value of the self-induced ernf d) all of the above
A uniform flux density of 1 T is perpendicular to the plane of a five-turn circular coil of radius 10 cm. Find the flux linking the coil and the flux linkages. Suppose that the field is decreased to zero at a uniform rate in 1 ms. Find the magnitude of the voltage induced in the coil.