A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action.

A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter13: Magnetic Induction

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

) A new manufacturing plant which operates on parameters such as temperature and pressure, has been procured by your company. In the operational manual is stated “if one or more than one parameter exceeds the safe value, a protective measure is needed to be done”. As an engineer, design a schematic diagram using an OR gate to detect the exceed parameter and explain how it will produce a command signal for the system to take the required action. Major Topic 12 Basic logic gates & its application AN
This question contains info on Digital Systems Logic Design and requires: Truth Table, KMapping and the Logic Circuits Designs. SEND the accurate answers labelled please.
Hello Sir,Good Evening I have a question in my home work related mechatronics lesson. The following below is my question. Please advise thank you. "Make a logic gate diagram and truth table from the following equation: F = (A . B) + C`
Need Part B (a) Suppose a two-way switch logic needs to be implemented in a staircase of a building, where a lamp can be controlled by two switches. You are required to analyze below conditions, and provide a PLC based system capable of operating according to the below mentioned conditions • If both the switches are in same state, i.e., both are off or both are on, then lamp will be in "ON" state. If anyone of the switches is "ON" and other is "OF", then lamp will be in "OFF" state. When the lamp is OFF, users can turn it on by changing the state of either switch 1 or switch 2. • Likewise, when the light is ON, users can turn off the light by changing the state of one of the two switches. 2. Suppose you are required to control a motor ON, OFF operation with two push buttons using PLC. Control System should work according to following conditions: When motor is off, and 1" push button is pressed, motor will start and stay in on state even after release of push button. When 2nd push…
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.
Q: Design an electronic system that represents some scenario created by you? (simple one that contains AND OR And NOT gates. ) Write a Boolean equation for it Design a circuit for it explain what your Scenario represents?
Simplify the logical expression seen in the accuracy table below using the karnough map method. Install the logical circuit that you get with the gate elements.
This is a logic gate simplification with certain laws to be followed. Please read the instructions on the given image, I will like your answer if you answered it properly and accurately. Thank you in advance
There are 5 gates in a metrobus, 1 of which is to get on and 4 to get off. The number of passengers inside is desired to be seen on the LCD connected to the P2 port. Get-on gate is controlled by the P0.2 while get-off gates are controlled by the P0.3, P0.4, P0.5, and P0.6. The sensors generate Logic-1 while passing passengers. Since the passenger carrying capacity of the metrobus is 294, if the number of passengers exceeds the number of 294, the warning LED connected to the P0.7 pin is required to light up. Since other pins of P0 are used for other purposes, it is not desired to be changed. Can you write the answer with assembly code using 8051 - AT89S8253 architecture?
Design a circuit using basic gates that accepts two decimal number of single digit and compute Binary Coded Decimal (BCD) number of each. The designed circuit then performs binary addition/subtraction in the following manner, When section mode pin is set to zero (0) the addition should be performed When section mode pin is set to one (1) the subtraction should be performed Use following bock diagram for circuit design and only provide details of the sub-circuits that are indicated with the sign of question marks only.
Create a schematic diagram and Truth Table for a logic circuit that is made up entirely of NOR gates of the given below:The scenario involves a circuit that has an alarm system, which activates a buzzer whenever both the power and at least one of the two sensors are turned on. It is important to note that the sensors will only function if an enable pin is activated.
A digital circuit whose number of inputs is 3, how many possible combinations of inputs will it have?