Answered: A non-magnetic circuit has a reluctance…

A non-magnetic circuit has a reluctance of 38.6 gilbert per maxwell. Calculate how much flux will be set up if surrounded by a 130-turn coil carrying 6.4-A of current. = maxwell

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.1MCQ: The Ohms law for the magnetic circuit states that the net magnetomotive force (mmf) equals the...

See similar textbooks

Related questions

Q: Find the current at 41 in the ff circuit. 14.₁ 45 4μ 501 3₁ 3^ = 100V IN

Q: Power spectral density of the signal given below is s (f) 2 -2 6 -6 ∞ 0 -1 1 1 2 f

Q: 1. Determine the values of Vs and Pvs. (if current through R₂ = 10 mA and R³ = 25 mA). Note: Use…

A: As per company guidelines we are supposed to answer only one question. Kindly repost other questions…

Q: A 250 kVA,480 V,3-phase,4 pole, 60Hz synchronous generator with a synchronous reactance of 099…

A: The per-phase equivalent voltage of the synchronous generator is, Vt=E3E=480 VVt=4803Vt=277.13 V…

Q: For a 3-phase, 4-wire system having balanced supply and unbalanced load, the following sequence…

Q: +16V 40 www to mm 2Η ΦΩ m 2Η 6 Ω 60

Q: Design the circuit that ICQ =1.5mA and Vc = 4V . Assume beta = 80 The B-E junction is fwd-biased…

Q: A 220 V self-excited shunt motor has armature and field resistances of 0.2 Ω and 220 Ω respectively.…

A: In this question we need to find a new speed in rpm (rev/min) if an external armature resistance of…

Q: 2) Goy(+ Find i, and i₂ 10 7 6 4 8 U2 Soy 7

Q: Q3: The matrix differential equation of the state variable model of a system has 0 1 ^-[- -8-12 8 -8…

A: Given matrix differential equation of state variable model of a system. Matrix be A.

Q: Let the periodic function be f(t) = |t| , -π < t < π . Solve the following points: a) Draw the graph…

Q: 3.6 Use nodalalysis to obtain u, in the circuit of Fig. 3.5

Q: conductors have an overall diameter of 3.0 cm each and are arranged in delta formation. Assuming a…

A: In this question we will find spacing between conductors for given critical disruptive voltage.....

Q: What is the significance of a negative indication of a wattmeter reading using the two-wattmeter…

A: In this question we will write significance of a negative indication of a wattmeter reading using…

Q: 3.41 Apply mesh ar lysis to find i in Fig. 3.87. Η ML 10 Ω 6V ΖΩ 4Ω wwww Μ 12 Μ Κ 1Ω 8V www 5Ω

A: In this question, We need to determine the unknown current i as shown the circuit using the mesh…

Q: 2. Given: F2(ABC) = (AB)C + (A'+B')' (a) Convert the expression into Standard Sum of product (SSOP)…

Q: f you have a 2pc battery and a 6w led, how many times does the battery discharge per hour? per…

A: In the above question 2pc will be 2c battery. It is a specification of battery. 2c battery =…

Q: Q.3 Obtain the unit-impulse response of a unity- feedback system whose open-loop transfer function…

A: given open loop transfer function Gs=2s+1s2given unity feedback so Hs = 1 given input is unit…

Q: R₁ www R₂ www R₂ o a b

Q: ►(1) FIGURE P4.17 n the translational mechanical system of e P4.17, where K = 1 and f(t) is a unit…

A: In this question , we will find mass and damping constant value for given system....

Q: 1. State or name one example of wired transmission media. 2. A type of transmission line that is…

A: 1. One of wire transmission media is telephone network, Telephone network : By this network…

Q: Given the magnetic circuit, calculate 3 from the right column if the coil wound in the left column…

A: Magnetic flux is the number of magnetic lines passing through the magnetic field. It is similar to…

Q: I need answer ASAP. Thank you! A.) Find the value of drain current and gate current. B.) What type…

A: Given: Consider the following circuit: To find: A) Find the value of drain current and gate…

Q: oscillations? 15.33 Consider the oscillator circuit in Figure P15.33. (a) Derive the expression for…

A: Frequency of the oscillation: This is also known as the oscillation frequency and the number of the…

Q: Determine the step response of the given parallel RLC circuit below that is for vc(t) at t ≥ 0…

Q: Find the equivalent G(s) = C(s)/R(s) for the system shown below. R(S) C(s) 20 10 s+12 10 Find the…

A: NOTE: As per guide lines I supposed to do only first three subparts, but according to your…

Q: 3.4 Given the circuit in Fig. 3.53, calculate the currents 7, through 14. 24 13 14 4A (1) 5Ω 10 Ω…

A: In this question we will find unknown currents...

Q: Q³: From the circuit, find the following:- 1- Vc. 2- Vout at 12 volt. 3- Vour at -12 volt. 4- Draw…

A: Brief description: In the above given question they want to know the value of output and the…

Q: C Q₂ Draw the circuit (A+B+C+D) using half and full a dobr which add four bits

Q: Q3/A/ A3-phase, 5.5kW, 440V, 501 Iz, cylindrical rotor S.M has synchronous reactance of (0+j2)…

A: Given data : Output power Pout=5.5 kW=5500W Synchronous reactance,Xs=j2Ω/ph Full-load…

Q: Find the T-parameters for the circuit shown below (do not use direct conversion). 5Ω 4 10 Ω 352 m ww…

A: In this question, We need to determine the T parameters of the given circuit?

Q: Q18. In the R-L-C series circuit shown, suppose R = 200 2, L = 70 mH, C = 2.0 μF, Vmax=80V and the…

A: As per guidelines given to us we can only provide the solution of first three subpart in multi part…

Q: Consider the sinusoidal voltage A. What is the maximum amplitude of the voltage? B. What is the…

A: Given, The sinusoidal voltage vt=80cos1000πt-30° V

Q: 4. Determine the impedance of the circuit of Figure 4.4 at frequencies of 1 kHz, 20 kHz and 1 MHz.…

Q: j 200 Figure 4.8 E L 10. For the circuit of Figure 4.8, determine the source current and the current…

Q: . A clothes 800 W iron is designed to be used with a 220 V outlet. How much current will flow in the…

Q: In a balance three-phase system, the source has an abc-phase sequence and is connected in delta. The…

A: Line voltage lead phase voltage by 30 degree in star connected system Line currents lag phase…

Q: Why are optical filters, such as a 690/50 bandpass, filter placed in front of photo-detectors?…

A: Given We need to enumerate the reasons why band pass optical filters are used infront of…

Q: Steady-state condition exist in the circuit shown in Fig.3 at t < 0.The switch is closed at t=0.…

Q: Q20. 1) Determine the finng angle required to deliv 1000W to the load. 2) Determine the RMS source…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: 22. Write the model equations for the network in Fig. 17,76, and find the voltage across the…

A: Given here a electrical circuit and asked to find the voltage across the capative element.

Q: Determine the z parameters for the circuit shown in below. 6Ω 5Ω ww + 4Ω V₂ 16 0.66V,

A: Z- parameter is used in two port network. Z- parameter analysis the power distribution networks…

Q: Q4.) A CRT has deflecting plats of 2cm longs, and 5mm a part. The screen is 500mm away from the…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: If there are two wattmeters being used to measure the total real power in a three-phase, three-wire…

A: Given: There are two wattmeter.

Q: In a series R-L-C circuit, the resistor has a reactance of 2 ohms, the capacitor has a capacitance…

A: Given: Series R-L-C circuitR=2ΩC=0.5FL=9H

Q: To ignite a mixture of gasoline and air inside an internal combustion engine--like in your car--a…

Q: R₁ www V10- Figure P9.28 *9.28 The circuit in Figure P9.28 is similar to the inverting amplifier…

A: As per bartleby guideline for more than one question asked only first is to be answered please…

Q: Instructions: Solve the following circuit problems and show your solution. 1. Determine the values…

Q: 1- Find the transfer function, for the network shown in Figure 1. 1H 1H 000 V₁ 1F 1F 10

Q: For the given circuit, Vin(20,-20), R-R KQ. What is the maximum and minimum values of Vout? Plot the…

A: Brief description: In the above given circuit diagram we need to know status of diode. After finding…

Question

how much flux

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A magnetic circuit consists of silicon steel of 3000 permeability and an air gap.The length of the steel core is 10cm and the air gap is 2cm. Both have the samecross section of 1.5 sq. cm. A current of 1⁄2 ampere flows through the windings toproduce 2351 maxwells flux. How many turns are there in the coil? ans: 5000 turns
A current of 200 mA passes through a coil of 300 turns wound on a core of length 50 cm, the relative permeability µr of which is 100. Calculate to find the magnetic flux density B setup within the core. Note that: µ0 = 4 π x 10-7 Hm-1
A square magnetic core has a mean path length 55cm and x-sectional area of 150cm2. A 200 turns coil of wire is wrapped around one leg of the core. The core is made of the material having relative permeability 3980. Find • How much current is required to produce 0.012 Wb of flux in the core • Calculate the reluctance and magnetomotive force.
1. A type material that is not affected by magnetic field. 2. If the number of turns is doubled, what will happen to the inductance? 3. It provides magnetic pressure which sets up or tends to setup flux in a magnetic.
A solenoid is 1 Cm long with a diameter of 0.5 Cm. The core is SiFe with a relative permeability of 4200. Assuming a current of 100 mA, what is the maximum number of turns for the winding that keeps the core under the saturation magnetic field of about 1.5 Tesla?
5. An 8-pole lap wound armature has 960 conductors and is run at 500 rpm. If the flux per pole is 40 mWb. Find the emf generated.a. 320 Vb. 315 Vc. 310 Vd. 318 V
The eddy current loss in a particular magnetic circuit is 10W/m3. If the frequency of operation is reduced from 50 Hz to 30 Hz with the flux density remaining unchanged, determine the new value of eddy current loss per cubic metre.
An iron-cored choke is designed to have an inductance of 12.5 H when operating at a flux density 3 T, the corresponding relative permeability of iron core is 1500. Determine the number of turns in the winding, given that the magnetic flux path has a mean length of 20 cm in the iron core and 2 mm in air-gap that its cross-section is 15 cm2. * ROUNDING OFF is ALLOWED only in the final answers expressed up to FIVE (5) DECIMALPLACES.
Which one of the following is not the function of pole shoes in a dc machine? (1) To reduce eddy current loss (2)To support the field coils (3)To spread out flux for better uniformity (4)To reduce the reluctance of the magnetic path (5)None of the above.
The magnetic circuit of Figure shown has current 10 A in the coil of 1800 turns. Assume that all branches have the same cross section of 2 cm^2 and that the material of the core is iron with μr = 1500. Calculate magnetomotive force for the core.
A magnetic circuit consists of silicon steel of 3000 permeability and an air gap. The length of the steel core is 10cm and the air gap is 2 cm. Both have the same cross-section of 1.5 sq.cm. A current of 1/4 A flows through the windings to produce 2351 maxwells flux. How many turns are there in the coil? Answer: ______ turns Through two parallel wires A and B, 10A and 2A of currents are passed respectively in opposite directions. If the wire A is infinitely long and the length of the wire B is 2m, then force on the conductor B, which is situated at 10 mm distance from A, will be ______ N.
2. The field coils of a six-poles D. C. generator each having 600 turns, are connected in series. On the excitation of the field, there is a magnetic flux of 0.024 Wb/pole. If the field circuit is opened in 0.24 second and residual magnetism is 0.0024 Wb/pole, calculate the average voltage which is induced across field terminals.instructions: Solve in step by step manner as possible for future referencesPlease illustrate properly and draw the solving Make sure to write it in a clean sheet of paper to review