A nozzle meter is connected with a pipe line to measure fluid flow rate as shown in Fig. 2. The diameter of pipe is 3 cm connected with 1.5 cm điameter nozzle. If the manometer differential height is 32 cm and water is flowing at 15 °C, determine the followings: (a) Calculate the average velocity through the pipe line (m/s) (b) If the diameter of pipe is increased to 4 cm, determine fluid behaviour either laminar or turbulent flow and how it will affect nozzle meter performance 32 cm Water 3 cm 1.5 cm Figure 2

A nozzle meter is connected with a pipe line to measure fluid flow rate as shown in Fig. 2. The diameter of pipe is 3 cm connected with 1.5 cm điameter nozzle. If the manometer differential height is 32 cm and water is flowing at 15 °C, determine the followings: (a) Calculate the average velocity through the pipe line (m/s) (b) If the diameter of pipe is increased to 4 cm, determine fluid behaviour either laminar or turbulent flow and how it will affect nozzle meter performance 32 cm Water 3 cm 1.5 cm Figure 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows at 0.07 cubic meter per second through a pipe. A horizontal venturi meter with throat diameter of 150-mm was used to measure the velocity inside the pipe. Based on manometer reading, the differential gauge is deflected 1.2 meter. If the specific gravity of the manometer fluid is 1.60, the velocity, in meter per second (m/s), of water inside the pipe is Blank 1
The pipe flow in the following figure is driven by pressurized air in the tank. The flow rate in the pipe is 50 cu.m./hr of water. Assume friction factor of the pipe f=0.014 and pipe diameter of 50mm. Calculate the needed pressure in the tank to provide the given flow rate, in kPa. Choices 1710, 1688, 1693, 1702
Calculate the discharge through a venturimeter connected to a differential manometer. The liquid present in the manometer is taken as mercury and the fluid flowing through the venturimeter is water. The difference between the level of mercury in 2 limbs of manometer is 30 mm. The diameter of inlet is 20cm and the ratio of the area of inlet and throat is 4. Assume the coefficient of discharge as 0.96.
Fluid mechanics- Bernoulli's Equation along a streamline: The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is twice that at station 1. Air with a density of 1.2kg/m3 flow through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of 10cm is measured. What is the velocity at station 2?
A 12-inch by 6-inch Venturi meter is installed in a vertical pipeline carrying water as shown inthe Figure C. The flow is upward through the meter. A differential manometer containing fluid,with sp.gr 1.67, is attached to inlet and throat, the difference z in gage levels being 5.76 ft.Neglecting loss of head, write energy equation from inlet to throat of meter. Also write stepby step equation of the differential gage between inlet and throat and combine the twoequations to compute the discharge
Pitot PipeBy connecting a mercury pressure gauge to a vertical pipeline through which water is transmitted, speed measurement is performed with a pitot tube. Since the deviation from the pressure gauge column is 15 cm, calculate the speed of the water in the pipe. (Pmercury=13560 kg/m3, Pwater=1000 kg/m3) (Answer is V2=6.08 m/s)
Fluid Water flows from a tank through a 2.6 m length of gal- vanized iron pipe 26 mm in diameter. At the end of the pipe is an angle valve that is wide open. The tank is 2 m in diameter. Cal- culate the time required for the level in the tank to change from 10 m to 2 m. Hint: Develop an equation for dh ⁄ dt where h is the level and t if time. Then solve this equation numerically.
For the venturi meter shown in figure 9, calculate the manometer deflection, h, if the velocity of flow of water in the 25mm diameter section is 10m/s
. A Pitot tube in the pipe in which air s flowing is connected to a manometer containingwater as shown in the figure. If the difference in water levels in the manometer is 87.5mm,what is the velocity of the flow in the pipe, assuming a tube coefficient, CP = 0.99?
1.) Water flows at 10m3/s in a 150-cm diameter pipe; the head loss in a 1000-m length of this pipe is 20.0m. Find the rate of energy loss due to pipe friction for the pipe. Use unit weight of Water : 9.79KN/m3.2.) Given the two dimensional flow as shown in the accompanying figure. Determine the flow rate considering 1.5m of width perpendicular to the figure.
(b) FIGURE Q2 shows a siphon used to drain water from a large reservoir. The diameters of the nozzle and the pipe are given by ddnn = 25 mm and ddpp = 50 mm, respectively. If the distances are given by XX = 4.6 m and YY = 0.9 m, calculate: (i) The flow rate through the nozzle (ii) The pressure at points A and B
The venturimeter has an air flowing through it with ᴕ=12 N/m3. The manometer shown below contains both mercury (S.G=13.6) and water. What is the actual volumetric flow rate of the air in L/s? The coefficient of discharge is 0.75.