A part is subjected to uniaxial compression stress of 40 MPa in the x- direction ( -40MPA). If the material's elastic modulus (E) is 100 GPa and Poisson's ratio is 0.35. What are the strains in the y-direction and z- direction? Eyy = 0.00014, Ezz = 0.007 0.00014, ɛ zz Eyy 0.00014 O Eyy -0.00014, ɛzz 0.00014

A part is subjected to uniaxial compression stress of 40 MPa in the x- direction ( -40MPA). If the material's elastic modulus (E) is 100 GPa and Poisson's ratio is 0.35. What are the strains in the y-direction and z- direction? Eyy = 0.00014, Ezz = 0.007 0.00014, ɛ zz Eyy 0.00014 O Eyy -0.00014, ɛzz 0.00014

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

Determine the bulk modulus for each of the following materials: (a) rubber, Er = 0.4 ksi, nr = 0.48, and (b) glass, Eg = 8(103) ksi, ng = 0.24.
If Poisson's ratio of a material is 0.5, then the elastic modulus for the material is a)three times its shear modulus b)four times its shear modulus c)equal to its shear modulus d)indeterminate
Can Young’s modulus have a negative value? What about the bulk modulus?
A pulley is keyed to a shaft midway between two bearings. The shaft is made of cold drawn steel for which the ultimate strength is 500 MPa and the yield strength is 450 MPa. The bending moment at the pulley varies from – 150 N-m to + 400 N-m as the torque on the shaft varies from – 50 N-m to + 150 N-m. Obtain the diameter of the shaft for an indefinite life. The stress concentration factors for the keyway at the pulley in bending and in torsion are 1.6 and 1.3 respectively. Take the following values: Factor of safety = 1.5; Load correction factors = 1.0 in bending and 0.6 in torsion Size effect factor = 0.85; Surface effect factor = 0.88
A shaft is subjected to an axial pull of ___ and transverse shear force of ___ The yield strength of theshaft materials is ___ and poison’s ratio 0.3. Determine the diameter of shaft using (i) Maximum Shearstress theory and (ii) Distortion Energy theory (iii) Maximum stress theory (iv) maximum strain energytheory (v) Maximum total strain energy theory. Also compare the obtained results Givin: Axial pull = 10kN Shear force = 8kN Yield strength= 100MPa Poison’s ratio = 0.3 FOS = 1.0
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
What is the Poisson's ratio if the ratio of Young's modulus (E) to the shear modulus (G) is 2?
a helical compression spring with squared and ground ends is to be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the coil diameter is limited to 22mm and the spring wire has a diameter of 3.71 mm, determine the stress concentration factor KsC
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
A pulley is keyed to a shaft midway between two anti-friction bearings. The bending moment at the pulley varies from – 170 N-m to + 510 N-m.The shaft is made of cold drawn steel having an ultimate strength of 540 MPa and yield strength of 400 MPa, Take σe = 0.5 σu. Determine the required diameter for an indefinite life based on Goodman equation. The actual stress concentration factor for the keyway is 1.6. The factor of safety is 1.5. Take size factor = 0.85 and surface finish factor = 0.88.
STRENGTH OF MATERIALS W/SOLUTION 1.) A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to? A. 2725 B. 1090 C. 545 D. 110 E. NOTA
A 11 in.in. inner diameter, 0.35 "" wall thickness pipe is under a pressure of 2.5 ksiksi where strain gages installed along axial and circumferential directions register strains of 180 and 900 micro-strains (x10−610−6), respectively. D) If the pipe is depressurized and then subjected to a torque of 50 lb - ft., it will experience a shear strain of ________ rad. 1.95x10-7 9.77x10-8 7.33x10-8 1.22x10-7 4.89x10-8