A permeability test was run on a soil sample with 8cm in radius and 10cm long. The level of water at point A and B from the datum is 18cm and 10cm, respectively. Determine the flow of water in cubic centimeter per hour that passes through the soil sample if the coefficient of permeability is 0.1383cm/sec. Point A Point B Soil Sample

A permeability test was run on a soil sample with 8cm in radius and 10cm long. The level of water at point A and B from the datum is 18cm and 10cm, respectively. Determine the flow of water in cubic centimeter per hour that passes through the soil sample if the coefficient of permeability is 0.1383cm/sec. Point A Point B Soil Sample

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.7P

See similar textbooks

Similar questions

For a falling a head permeability test, the following data were recorded. Length of soil specimen = 500 mm. Area of soil specimen = 16 cm2 Area of stand pipe = 0.97 cm2 Head difference at time t =0 is 760 mm. Head difference at time t = 6min. is 410mm. The test was conducted at a temp. of 20 ֯C. with a unit wt. of water equal to 9.789 kN/m3 and the viscosity of water at 20 ֯C is 1.005 x 10-3 N.8/m2 . Compute the hydraulic conductivity of the soil. Compute the absolute permeability of the soil. What is the head difference at time t = 4 min?
For a falling head laboratory test, the following are the given values:• Length of soil specimen = 210.00 mm• Initial head = 523.00 mm• Final head = 297.00 mm• Duration of test = 3.50 mins• Area of standpipe = 42.0 sq.mm• Area of specimen = 1050.00 sq.mmA. Compute for the hydraulic conductivity of the soil in cm/sec.B. Determine the seepage velocity if n=0.35C. Determine the head difference at t = 120 sec
For a falling head permeability test, the following are given: length of specimen is 360 mm, area of specimen is 70 cm2 , and hydraulic conductivity of soil specimen is 0.165 cm/min. what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins? compute the seepage velocity under the test condition if the soil specimen has a void ratio of 0.55 in cm/sec compute the head difference at time equal to 5 minutes?
The data from a falling head test is shown Diameter of the standpipe = 3cm Initial head = 91.77 cm duration of the test = 18 mins length of the soil sample = 32.98 cm diameter of the permeameter = 44 cm If the soil permeability id 0.005cm/min, determine the final head (in cm) of the permeability test.
Sketch the figure and determine coefficient of permeability (k) in mm/min using constant head permeability, given the following data, Water flows horizontally The height of the reservoir supply source is 2 m above the elevation of the outlet. The soil sample length in the direction of water flow is 200 mm. The cross-sectional area of the soil sample is 1,950 mm2. The measured volume of flow for the steadystate condition is 500 ml in a 10-minute time period.
FUNDAMENTALS OF GEOTECHNICAL ANALYSIS A constant head permeability test is performed on soil that is 2 cm x 2 cm square, and 2.5cm long. The head difference applied during the test is 20 cm and 7 cm3 is collected over a time of 100 sec. a) Compute the permeability based on these test conditions and results. b) A falling head test is conducted on the same soil specimen at the same time (t1 – t2 = 100 sec), and the standpipe diameter is 0.8 cm. If the average head during the test should be 18 cm, what are h1 and h2 values?
A block of soil in a permeability test has a length of 120 mm and a cross-sectional area of 600 mm2. The water level at one end is 200 mm above a fixed datum and at the other end is 30 mm above the same plane. The flow rate was 2 ml in 90 seconds. Compute the coefficient of permeability of the soil in m/s. a.2.61 x 10-5 m/s b.0.98 x 10-5 m/s c.1.78 x 10-5 m/s d.3.97 x 10-5 m/s e.1.89 x 10-5 m/s
49. A pumping test was made in a sand layer extending to a depth of 16m. The initial groundwater table was located 2m below the ground surface. Observation wells were sighted at distances 4m and 9.5m from the pumping well. Using a discharge of 0.4 cubic meters per hour, a steady level is attained at the pumping well. The measured drawdowns at the two observation wells are 2m and 0.25m respectively. Determine the coefficient of permeability of the soil.
For a falling or variable head permeability test, the following are given: Length of soil specimen = 12 cm. Cross sectional area of stand pipe: A = 0.018 cm2 Diameter of soil specimen = 7.5 cm. Time of collection of water: t = 65 sec. Head difference at time t = 0; h1 = 70 cm. Head difference at time t = 65 sec; h2 = 40 cm. Temperature of water: 14 ֯C Find the absolute permeability of the soil at 20 ֯C.
A soil sample 14 cm in diameter is placed in a tube 1m long. A constant supply of water is allowed to flow into one end of the soil at A and the outflow of B is collected by a bearer. The average amount of water collected is 1.4 cubic centimeter every 8 seconds. The tube is inclined and has a head difference of 2.3 m. Give the seepage velocity if porosity is 0.291.
Find the flow rate of water in cm3 /s if the value of soil permeability is 0.9 cm/s, hydraulic gradient is 1.25, and the diameter of the soil specimen is 175 mm.
A block of soil in a permeability test has a length of 120 mm and a cross-sectional area of 600 mm². The water level at one end is 200 mm above a fixed datum and at the other end is 40 mm above the same plane. The flow rate was 2.5 ml in 95 seconds. compute the coefficient of permeability of the soil in m/s.