A person's toe displacement is measured by video analysis during running. The raw coordinates are contaminated by pure 50 Hz noise with an amplitude of ±1 mm. The raw data is not filtered prior to the calculation of acceleration. What will the magnitude of the noise component within the acceleration signal be? a. ± 1 mm b. ± 50 mm O c. ± 250 mm O d. ± 2500 mm

A person's toe displacement is measured by video analysis during running. The raw coordinates are contaminated by pure 50 Hz noise with an amplitude of ±1 mm. The raw data is not filtered prior to the calculation of acceleration. What will the magnitude of the noise component within the acceleration signal be? a. ± 1 mm b. ± 50 mm O c. ± 250 mm O d. ± 2500 mm

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.22P

See similar textbooks

Similar questions

When the unit step function is applied to the input of the control system given below, the peak time of the output signal is 0.47 s and the settlement time is 0.91 as. It is also known that the steady state error of the system is 10% for the same input. In this case, what is the damping rate of the system? calculate.
What is the steady-state error component of the system from R(s) when applied to the inputs of the control system given below? and What is the steady-state error component from D(s)? Calculate.
Q1. Consider the following characteristic equations. Determine the values of K that corresponds to a stable system. Use the Routh-Hurwitz criterion.
9.- Consider that the serial velocity is given by: baud_rate=Fosc/k(n+1) With k and n (integers) It is required to communicate at 1200 bps with a 1MHz clock and K=16 n=5. The error expression iserror=(real_baud_rate - ideal_baud_rate)/ideal_baud_rate What is the % error in this case?
Reduce the block diagram a) Reduce the block diagram b) Replace the values (c) Use the Routh-Hurwitz criterion to determine the stability of the system, is the system stable? is the system stable?
Derive the formulations of settling time, damping ratio, peak time, overshoot and rising time for 2% and 5% error criterion. "Transient response parameters of 1st and 2nd order systems" t_s = ? t_p = ? t_r = ? sigma = ? w_n = ? M_p = ?
Find the Routh-Hurwitz criteria table for this equation
A permanent magnet loudspeaker is equipped with a10 ohm voice coil wound on a tube 1 inch in diameter. Theflux density in the air gap is 10,000 lines per square inch. If the impedance of the voice coil is a pureresistance, what will be the maximum thrust delivered to the core if the impressed signal is 20 dB above 0.005watt? Ans: _____ mN
What is the difference (comparison) between the capability of variation of parameters method and the undetermined coefficients – superposition approach when solving non-homogeneous linear higher-order differential equations?
H6. Pianos have two or three strings for each note. A piano tuning system called beats occurs as a forced undamped oscillator model when the frequency of excitation is almost equal to the natural frequency of vibration. Suppose the natural frequency of the oscillator is exactly 1/? and that the frequency of the driving function is (1 + ?)/? where ? is a small number, either positive or negative. a) Write a differential equation with the assumed characteristics. b) Find the general solution of the differential equation written in item a) when ? = −0.1
Find: Static position, velocity, acceleration error coefficients, and corresponding steady state errors. G(s)= K(2s+1)(4s+1)/s2(s2+2s+10) Note: This is a open loop function, input signal are unit step, unit ramp and parabolic. I need answer ASAP. Thank you!
Oscillations are typical of closed-loop responses when this mode of control is used.A. proportionalb. on/off c.integral d.derivative Which mode of control effectively eliminates offsets in the controlled variable?a. integral b. on/off c. proportional d. derivative Which of the following is not a requirement for the Routh stability test? a. all coefficients positive b. even-degree polynomial c. polynomial characteristic equation d. terms arranged in standard order