•Figure below shows a voltage to current converter Op. Amp. Circuit. Find the value of the load current I in terms of the circuit components, R₁, V₁ and V. Design the circuit to drive a dc motor with load current I of 20mA from digital drive voltage of 5V connected to the input of the op. amp. Circuit. 5V R + R 20mA IL dc motor 5V R₁

•Figure below shows a voltage to current converter Op. Amp. Circuit. Find the value of the load current I in terms of the circuit components, R₁, V₁ and V. Design the circuit to drive a dc motor with load current I of 20mA from digital drive voltage of 5V connected to the input of the op. amp. Circuit. 5V R + R 20mA IL dc motor 5V R₁

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

of a Flyback converter with Circuit parameters given below.Circuit Parameters;Input Voltage Vs= 48 VN1/N2=3Lm=500 μHR=5ΩC=200 μFSwitching frequency f=40 kHzOutput Voltage Vo=10 Va) Duty Cycleb) In terms of magnetization inductor (Lm); mean, maximum andtheir minimum values;c) Find the output voltage fluctuation. (All components are ideal.assume.)
a)A 3-phase full converter delivers power to a load R=50 ohms. the source voltage is 400V,50Hz.For a firing-angle delay of 45 degrees, find the power delivered to the load R.(b)A single phase fully-controlled bridge converter supplies a load drawing constant ripple free current. if the firing angle is 30degrees.find the input power factor.
Figure 1 shows the equivalent circuit of a voltage amplifier with a source and aload connected to its input and output, respectively. Suppose that the sourceinternal resistance is Rs = 5 kΩ, the amplifier input resistance is RIN = 95 kΩ, theamplifier gain is A = 100, the amplifier output resistance is ROUT = 150 Ω and theload resistance is RL = 5 kΩ. For a sinusoidal input with amplitude VS = 5 mV, whatis the amplitude of the voltage VL across the load resistor RL? What would thevoltage across the load be without the amplifier?
a) Demonstrate input and output waveform of single phase Cyclo-converter such that output frequency is 1/3 of input supply frequency with circuit diagram. b) Perform the calculation to analyze (i) output RMS voltage and (ii) input power factor of single-phase AC voltage controller as shown in the following figure. Suppose converter has a resistive load of R=‘A’ Ohm and the input voltage is Vs=220, 50Hz with a delay angle of π/3. A= 4
A single phase full converter feeding RLE load has 230 V, 50 Hz source, R=2.5 ohm, E=100 v, firing angle=30° If the load inductance is large enough to make the load current virtually constant Find average of output voltage, output current and power factor.
Figure Q3 shows a single stage transistor amplifier driven by a signal voltage source Vi a) Determine the operating (Q) point if B = 100 and VBE = O.7 V. b) Using the re model, draw the AC equivalent circuit and determine the: i) input impedance, output impedance, ii) voltage gain AVs iii) the current gain, Ai. Assume ro = ∞
In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
The converter is operated form a three phase Y- connected 208V, 60hz supply and the load resistance is R= 10 ohms. If it is required to obtain an average output voltage of 50% of the maximum output voltage, calculate the a, Delay angle b, rms and verage output current c. The average and rms thyristor currents d. the rectification efficiency
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
1. PLEASE SOLVE AND SHOW YOUR DETAILED SOLUTION WITH FBD. A parallel circuit consisting of a resistor, an impedance coil, and a capacitor of negligible loss is connected across a 120-volt 25-Hz supply and takes a current of 4.3 amp. The current to the resistor is 3.6amp, that of the capacitor 2.5 amp, and that to the impedance coil, 3.2 amp, Determine the power-factor angle and power of the entire circuit.
In the Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: In the voltage range [ AB ] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (uF) 5) Pload 2 H (Watts) consumed per load The lowest L inductance value that can keep the DC-DC converter in continuous current condition under Which option do you see below as pH ? A = 10 Volts B = 19 Volts M = 23kHz F = 26 Volts H = 8 Watts
Q2) B) In a step-up converter, the duty ratio is adjusted to regulate the output voltage at 48V. The converter is supplied by a solar cell panel where its output voltage varies in a wide range as shown in the following V-I characteristics (Fig.PE-1). The maximum power output of the converter is 120 W. For stability reasons, it is required that the converter always operate in a CCM mode. The switching frequency is 50kHz. Assuming ideal components and C as very large, calculate the maximum value of L that can be used.