A piece of 12-gauge sheet metal is 7⁄64 inch thick. A stack of sheet metal is171⁄2 inches thick. How many sheets are in the stack?

Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece. Select…

A: Solution:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: Join two pieces of metal that are .045 and .045 thick. The joint is made with a triple row of…

A: We have given that, The joint is made with a triple row of MS20426 rivets. here, MS20426 means ,…

Q: , I want to know what would be the perfect size to put a bushing in a hole. The bushing will have a…

A: Given information about the workpiece:

Q: A 7 mm diameter copper bar is to be cold worked 69 %. Find the final diameter (mm). Round your…

A:

Q: The spanners used in workshop are made using ___________ process. a. Forging b. Extrusion c. Drawing…

A: Solution:

Q: Q1/ A:1. For the triangle shown in the (fig.1) below; Determine the length of (AC); (L)

A: Given data: Length of perpendicular side BC, P = 15 cm. Length of base side AB, B = 20 cm. Part…

Q: How much scrap pipe will be left if a 13-ft 6in. piece is cut out of a 20-foot length of pipe?

A: total length of pipe=20'cut piece length of pipe=13'6"

Q: 9. the force acting along a line equal to magnitude of force times... *

A:

Q: 31. A 75-foot by 75-foot by 4-inch-thick slab is poured over the metal deck shown in Figure 5-25.…

A: The expression for the average thickness is given by, Here, t represents the thickness of the metal…

Q: | X2 F m

A:

Q: can you please write it in a proper way?

A:

Q: What is the force produced by an actuator to open a valve if its diaphragm has a 4-inch diameter and…

A: Given data:

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Consider a 146 ft long, 4 in. type M copper tubing. What is the outside diameter in inches? (Round…

A: For a copper tube of M type and 4 in size - The outer diameter is 4.125 inches.

Q: A slender rods Subgected to tenston, the lood is increased incrementally and the plot at left…

A:

Q: A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length…

A:

Q: how would this look like if written?

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: A piece of frame material is 50’ long.  If we cut it into 6. 25" long pieces, how many pieces will…

A:

Q: Given; A = 500 mm2, Load 1 = 25 kN, Load 2 = 50 kN. Solve the stress in Part BC. (Write answer in 2…

A:

Q: Please show all work and answers. If not ALL then please answer ones in RED. Thank you.

A:

Q: G. A line 32 mm long joins to towns on a map of scale 1:100,000. (a) How far apart are the towns to…

A: For solution refer below images.

Q: The height (in mm) for a 125 mm sine bar to measure a taper of 27'32' on a flat work piece (correct…

A: Given:Length of sin bar, L=125 mmθ=27o 32'θ=27+3260oθ=27.533o

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: Determine the total increase in length.

A: Given: E1=175 GPa E2=210 GPa P=55 kN To determine: Total increase in length

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: An irregular shaped metal sheet is to be constructed with a measurement of 5.5m x 6.2m x 7.7m x 4m x…

A: given; dimension of irregular shape of sheet metal;          (1m=39.3701inch)L1=5.5m=5.5*39.3701…

Q: in figure, the length of wire

A: GIVEN:

Q: Complete the each drawing by adding the missing details in 5 and 6 both questions.

A:

Q: Two 12' bars are cut into pieces 8-3/8" long and the saw kerf is 1/8" (waste). How many pieces can…

A: Given Data:- Length of each bar, L=12’

Q: Given the drawing below, answer questions

A: 11) For G dimension Since, G = 3-0.3+0 So, basic size = 3 Tolerance = 0-(-0.3) = 0.3 Maximum size =…

Q: Two parallel shafts, 36 inches apart are connected by a belt drive. The driving pulley rotates at…

A: GIVEN DATA DISTANCE BETWEEN SHAFT C=36in smaller pulley dia d=10in Larger pulley dia D=24 in We…

Q: 4. What is the cost of 23' of cable if 34' costs $76.00? (round to nearest dollar)

A: Given-            Cost of 34ft cable=$76 To be determine-             Cost of 23ft cable

Q: A mild steel specimen of Initial diameter of 51.5 mm is turned to final diameter of 48 mm for an…

A: here 4  subparts were posted, As per honor code and answering guidelines I can answer firs 3…

Q: 4. What is the length of the longest part?

A: To find Length of longest part.

Q: The best size wire is fitted in a groove of a metric screw such that the wire touches the flanks of…

A: Given:p=4 mmθ=60°

Q: On the attached part print, what is the diameter of the part at points "D" and "E"?

A: On observing the front and side view of the figure it is clear that the diameters of all the…

Q: a) Create a sketch of the Figure 2 as below (.ipt) b) Extrude the sketch in a) by a thickness of 1mm…

A: According to the details provided in the question, we need to DRAW the figure.  i am using the…

Q: What rate of interest compounded annually is the same as the rate of interest of 6% compunded…

A:

Q: Bending causes increase in the thickness of the sheet metal.

A: Bending is a manufacturing process in which sheet metal is bend to obtain different shapes.

Q: (a) Shear the following triangle. Explain what measurements change and what stays the same,…

A: shearing is the change of shape of triangle or parallelogram but base of both triangle and…

Q: If a drawing has 6 fillets with radius (1/2 inch) for imperial units drawing, name one way that you…

A: If a drawing has 6 fillets with a radius (1/2 inch) for imperial units drawing, the one way that we…

Q: Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.