A pipe of 60 meters long and 150 mm in diameter is connected to a water tank at one end and flows freely into the atmosphere at the other end. The height of water level in the tank is 2.6 meters above the centre of the pipe. The pipe is horizontal and f = 0.01. Determine the discharge through the pipe in litres/s, if all the minor losses are to be considered. V I

A pipe of 60 meters long and 150 mm in diameter is connected to a water tank at one end and flows freely into the atmosphere at the other end. The height of water level in the tank is 2.6 meters above the centre of the pipe. The pipe is horizontal and f = 0.01. Determine the discharge through the pipe in litres/s, if all the minor losses are to be considered. V I

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing upward through a tapering pipe of height 1 m at the rate of 0.28 cumec. Thediameters at the lower and upper ends of the pipe are 300 mm and 600 mm, respectively. If pressure atthe lower end of the pipe is 0.981 bar, determine the force exerted on the tapering pipe and itsdirection. Neglect the losses of energy and the weight of the pipe.
Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m
Following the pump, the pressure in a 6-inch inner smooth pipe conveying water is 20 pounds per square inch (psia). The water is released into a 100-foot-long open tank located from the pump. Prove that the rate of discharge of water in cubic feet per second (ft3/s) is 3.58 ft3/s.
Two water reservoirs, A and B are 8km apart and are connected by a 750 mm diameter steel pipe( f=0.02). Reservoir A is 10 m higher than reservoir B. If the pressure at B is 4 kg/cm^2 greater than at A, determine the amount and direction of flow of water inside the pipe. Disregard minor losses.
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
Oil flows from a tank through 150 m of 150 mm diameter pipe andthen discharges into air as shown. If the head loss from point 1to point 2 is 600 mm, determine the pressure needed at point 1 tocause 17 L/s of oil to flow.
The water flows through a taper pipe of length 100m having diameters 0.6m at the upper end and 0.3m at the lower end at the rate of 0.05m3 /s. If the pressure at the higher level is 196.2 kPa and the pipe has a slope of 1 in 40, then determine the pressure in the lower end.
A simple pitot tube and a piezometer are installed in a vertical pipe as shown in the figure. If the deflection in the mercury manometer is 0.1 m, then determine the velocity of the water at the center of the pipe. The densities of water and mercury are 1000 kg/m3 and 13600 kg/m3 , respectively.
The diameter of a pipe changes from 200mm at a section 5 meters below a datum to 50mm at asection 3 meters above datum. The pressure of water at first section is 500kPa. If the velocity of flowat the first section is 1m/s, determine the intensity of pressure at the second section.
Intravenous infusions are usually driven by gravity by hanging the fluid bottle at sufficient height to counteract the blood pressure in the vein and to force the fluid into the body. The higher the bottle is raised, the higher the flow rate of the fluid will be. (a) If it is observed that the fluid and the blood pressures balance each other when the bottle is 1.2 m above the arm level, determine the gage pressure of the blood. (b) If the gage pressure of the fluid at the arm level needs to be 20 kPa for sufficient flow rate, determine how high the bottle must be placed. Take the density of the fluid to be 1020 kg/m3.
Determine the manometer reading as shown in thefigure, when the velocity of fluid flowing through a75mm diameter pipe is 0.6 m/sec.
Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a 150-mm 90 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 85mm. If the pressure just before the elbow is 95 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.