A piston-cylinder device equipped with a spring initially contains 0.1 kg of steam at 200 kPa. At this state, the steam occupies a volume of 0.01 m'. The position of the spring is that it will only starts to be compressed when the volume of steam reaches 0.05 m. Heat is continuously transferred to the system until the final pressure doubles from the initial state. If the final temperature of steam is 800°C, determine:

A piston-cylinder device equipped with a spring initially contains 0.1 kg of steam at 200 kPa. At this state, the steam occupies a volume of 0.01 m'. The position of the spring is that it will only starts to be compressed when the volume of steam reaches 0.05 m. Heat is continuously transferred to the system until the final pressure doubles from the initial state. If the final temperature of steam is 800°C, determine:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tank, well insulated, has two parts divided by partition. The first part incuded 5,5 kg of water at 600 kPa while the other part is evacuated. This partition is removed and the water expands to fill the entire tank. If the final pressure and temperature are 250 kPa and 150 0C, respectively, please determine The volume of the tank Temperature of the water for first part
A rigid vessel contains 5 kg of wet steam at 0.4 MPa. After the addition of 9585 KJ, the steam has a pressure of 2.0 MPa and a temperature of 700°C . Determine the initial internal energy the specific volume of the steam .
From a temperature of 250 degrees Celsius, superheated steam is compressed at a constant pressure of 280 kPa until it reaches the saturated vapor phase. Determine the process's work in kJ per kg of steam.
2. A rigid vessel contains 5kg of wet steam (water) at 0.4 MPa. After the addition of 9585 kJ of heat the steam has a pressure of 2.0 MPa and a Temperature of 7000C Determine (a.) the initial quality, (b.) initial internal energy and (c.) initial specific volume of the steam.
Steam is contained in a 4-L volume at a pressure of 1.5 MPa and a temperature of 400 C. If the pressure is held constant by expanding the volume while 20 kJ of heat is added, the final temperature is nearest
A piston-cylinder device initially contains 0.8 m^3 of saturated water vapor at 275 kPa. At this state, the piston is resting on a set of stops, and the mass of piston is such that a pressure of 500 kPa is required to move it. Heat is now slowly transferred to the steam until the volume doubles. Show the process on a P-v diagram with respect to saturation lines and determine (a) the final temperature, (b) the work done duringthe process, and (c) the total heat transfer.
A rigid vessel contains 5kg of wet steam (water) at 0.4 MPa. After the addition of 9585 kJ of heat, the steam has a pressure of 2.0 MPa and a temperature of 7000C Determine (a) the initial quality, (b) internal energy, and (c) specific volume of the steam.
Ms Png works on a piston-cylinder system which contains 0.05 m3 of nitrogen gasinitially at 200 kPa. At this state, a linear spring that has a spring constant of 150kN/m is touching the piston, but no force is exerting on it. Heat is then transferredto the nitrogen gas, causing the piston to rise and to compress the spring until thevolume inside the cylinder increases to 0.25 m3.a) Determine the final pressure inside the cylinder.b) Sketch the system on a P – V diagram.c) Calculate the total work done of the system.d) Deduce the work done against the spring to compress it.Given cross-sectional area of the piston = 0.25 m2Force applied by linear spring, F = kxk = spring constantx = displacement of the piston/spring
A piston-cylinder device contains 50 kg of water at 250 kPa and 25°C. The cross-sectional area of the plunger is 0.1 m2. Heat is transferred to the water, causing some of it to evaporate and expand; When the volume reaches 0.2 m3, the piston hits a linear spring whose spring constant is 100 kN/m. More heat is transferred to the water until the plunger rises a further 20 cm. Determine a) the final pressure and temperature and b) the work done during this process. Also show the process on a P-V diagram.
Determine the quality of steam at 169.06 kPa when 270 kJ/kg of energy are lost from saturated steam. What is the steam temperature?
12kg of R-134a fill a 0.8m30.8m3 weighted piston–cylinder device at a pressure of 280kPa280kPa. The container is now heated until the temperature is 50°C50°C. Determine the initial temperature and final volume of the R134a.
A piston-cylinder device contains 0.5 kg of air initially at 3 MPa and 250°C.The air is first expanded at the constant pressure to 0.04 m3, thencompressed isothermally to the initial volume, and finally compressedisometrically to the initial state.1. Draw the P-V diagram.2. Determine the boundary work for each process and the net work of thecycle.3. Heat lost during the constant volume process.