A piston-cylinder system contains R-134a as shown in the figure. Two linear springs with the same spring constant but different lengths are installed above the frictionless piston. Initially (state 1) the piston is motionless and floating so that the top of the piston is 2 cm from the bottom of Spring 1 and 5 cm from the bottom of Spring 2. In this initial state the R-134a has a temperature of T, = -20°C and a quality of 70%. Heat is added to the system causing the piston to rise until it just touches Spring 1, but Spring 1 exerts no force on the piston. In this state (state 2), the R-134a has a volume V2 = 30 L. Heating continues until the temperature reaches T3 = 50 °C and Spring 1 is compressed until the piston just touches Spring 2, but Spring 2 exerts no force on the piston (State

A piston-cylinder system contains R-134a as shown in the figure. Two linear springs with the same spring constant but different lengths are installed above the frictionless piston. Initially (state 1) the piston is motionless and floating so that the top of the piston is 2 cm from the bottom of Spring 1 and 5 cm from the bottom of Spring 2. In this initial state the R-134a has a temperature of T, = -20°C and a quality of 70%. Heat is added to the system causing the piston to rise until it just touches Spring 1, but Spring 1 exerts no force on the piston. In this state (state 2), the R-134a has a volume V2 = 30 L. Heating continues until the temperature reaches T3 = 50 °C and Spring 1 is compressed until the piston just touches Spring 2, but Spring 2 exerts no force on the piston (State

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

cylinder device contain air with a mass equal to m = 075 kg. a quantity of heat is added to it with a constant pressure as a result the temperature increased by 7 degrees. determine the work done the gas constant is 0.287kJ/kg.K
Consider a vertical spring-loaded piston cylinder. The gas inside the cylinder has a pressure of 130 kPa. And the spring exerts a downward force of 200 N on the top of the piston. The diameter of the piston is 10 cm and the atmospheric pressure is 1 bar. Determine the mass of the piston that will maintain equilibrium. Neglect the friction effects between the surface of the piston and the cylinder.
What is the solution of this problem?
A piston cylinder device contains B kg of water at A ° C. The frictionless piston with an area of C m2 initially rests on the stoppers and its cylinder volume is 0.03 m3. The pressure in the cylinder must be D kPa for the piston to activate. As the piston moves upwards, when the cylinder volume is 0.075 m3, it touches the linear spring with a spring coefficient of 360 kN/m. Since the final pressure is E MPa, by showing the state change together with the saturation curves on the P-V diagram, a) The water temperature in the last case,b) The work done during the transaction,c) Calculate the total heat transfer. Note: If you think there is missing data, you can choose appropriate values by making the necessary explanations.
1-kg ice has 7% more volume than 1-kg water. You fill a cast iron container with water at 0°C and close it tight without any escape for water inside so that when you freeze the water, all the water inside turns into ice at 0°C. When all the water freezes, what would be the pressure increase inside the container, if the bulk modulus of water is 6X109 N/m2. Give your answer in as the number a in aX109 N/m2. g=9.8 m/s2
A mass of ice at -7 C is needed to cool 224 kg of vegetables (Cp = 3.35 KJ /kg.K )in a bunker for 24 hours. The initial temperature of the vegetables is assumed to be 29 C . It is also assumed that the average temperature in the bunker is 7C within the 24 -hour period . If the heat gained per hour in the bunker is 25% of the heat removed to the vegetables from 29 C to 7C, what would be the required mass of ice ? show t-s diagram
Air is contained in a vertical piston–cylinder assembly fitted with an electrical resistor. The atmosphere exerts a pressure of 101.325 kPa on the top of the piston, which has a mass of 50 kg and a face area of 0.2 m2. The volume of the air slowly increases by 0.085 m3 while its pressure remains constant. The mass of the air is 0.45 kg and its specific internal energy decreases by 25 Btu/lb. The air and piston are at rest initially and finally. The piston–cylinder material is a ceramic composite and thus a good insulator. Friction between the piston and cylinder wall can be ignored, and the local acceleration of gravity is g = 32.0 ft/s2. Determine the heat transfer from the resistor to the air, in Btu, for a system consisting of the air and the piston. Select one: a. -16.64 Btu b. 33.36 Btu c. -6.25 Btu d. 19.16 Btu
A fluid, contained in a horizontal cylinder fitted with a frictionless leak proof piston, is continuously agitated by means of a stirrer passing through the cylinder cover. The cylinder diameter is 0.40 m. During the stirring process lasting 10 minutes, the piston slowly moves out a distance of 0.485 m against the atmosphere. The net work done by the fluid during the process is 2 kJ. The speed of the electric motor drivingthe stirrer is 840 rpm. Determine the torque in the shaft and the poweroutput of the motor.
5. A 0.8-m3 rigid tank contains nitrogen gas at 600 kPa and 300 K. Now the gas is compressed isothermally to a volume of 0.1 m3. Solve for the work done on the gas during this compression process. (3 DECIMAL IN FINAL ANSWER PLS)
consider a vertical spring loaded piston cylinder. The gas inside the cylinder has a pressure of 130kpa.and the spring exerts a downward force of 200N on the top of the piston. The diameter of the piston is 10 cm and the atmospheric pressure is 1 bar. Determine the mass of the piston that will maintain equilibrium. Neglect the friction effects between the surface of the piston and the cylinder.