A plant located at an altitude of 925 m has an open feedwater heater located 2.76 m above the pump intake. The water in the heater has a temperature of 65ºC. If the head loss in the suction line is 0.8 m. Determine: a. Atmospheric pressure head, in meter b. Vapor/saturation pressure head, in meter c. The Net Positive Suction Head

A plant located at an altitude of 925 m has an open feedwater heater located 2.76 m above the pump intake. The water in the heater has a temperature of 65ºC. If the head loss in the suction line is 0.8 m. Determine: a. Atmospheric pressure head, in meter b. Vapor/saturation pressure head, in meter c. The Net Positive Suction Head

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 25RQ

See similar textbooks

Similar questions

1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
4. Diethyl ether (SG=0.71, viscosity: 0.224 cp), which is the product from a distillation process, is being condensed in a tank shown in the figure and pumped away as liquid. The total pressure in the condenser is equal to the vapor pressure of diethyl ether which is 450 mmHg. Flow rate of the diethyl ether is 120 kg/min. Losses in the pipe between the condenser and the pump can be estimated as 15 J/kg. Vapor Condenser P=450 mmHg Cooling Water ho=? (a) If the net positive suction head of the pump is 3 m of liquid, what must be the least height of the liquid level in the condenser above the pump inlet?
In a cast-iron piping system of 450 ft length shown below, the rate of flow is 1 cfs at 70°F. Assuming the total head losses for the flow in the system is 10 ft, what is the energy head supplied by the pump E? a. 40 ft b. 50 ft c. 60 ft d. 510 ft e. None of the above
For the purpose of acting as an air-cooled water chiller, an ammonia refrigerant vapor compression system is deployed. It is functioning with an evaporator temperature of 0 degrees Celsius and a condenser temperature of 40 degrees Celsius. The refrigeration produced by the system is equal to 15 tons.Find out: a. The temperature of the discharge and the mass flow rate of the refrigerant that is being circulated.b. The piston displacement that can be considered theoretical for the compressor.c. The work that can be done by the theoretical compressor.d. The heat that is not allowed to escape through the condenser.e. The Carnot coefficient of performance and the actual COP of the cycle.f. The volume of air that is supplied in the condenser if the air comes in at 30 degrees Celsius and exits at 34 degrees Celsius.g. The LMTD and AMTD of the condenser h. The water flow rate of the chiller assuming that the water enters the evaporator at 10 degrees Celsius and exits at 5 degrees Celsiusi. The…
12. The condenser pressure 600 mm Hg vac. The surrounding condition is at 760 mm Hg. Determine the equivalent condenser pressure in bars absolute. a. 0.2133 c. 0.6123 b. 0.4313 d. 0.8542
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)
Waters enters the condenser at 20°C and leaves at 35°C. what is the log mean temperature difference if the condenser temperature is 45°C?(°F)
A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
Q2- Water ( p= 990 kg/m & u= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
Design a simple piping system to pump water at temperature 130F from a sump below a heat exchange to the top of the cooling. The desired flow rate is 222gal/min, and the pump efficiency is 88%. Include the required power and head loss of the pump and the total head loss.
How high must the pump centerline be located above the water level in an open tank that supplies water to the pump if it requires a minimum of 2.5m of NPSH? The barometer reading is 760mmHg, the pipe friction is 0.65m and the vapor pressure is 3.51kPa. 6.82m 5.48m 7.39m 4.99m
For a 10-ton-capacity refrigeration system, the pressure of refrigerant in the evaporator is 150 kPa, whereas in the condenser it is 950 kPa. If refrigerant R-134a is used under saturated conditions, calculate the theoretical power required to operate the compressor = ... KW