Answered: A plate made of mild steel having 10 cm…

A plate made of mild steel having 10 cm thick, maintaining temperature 250°C. The convection & radiation heat transfer are 2 kw & 1 kw respectively. Find heat conduction through the plate?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Related questions

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

Q: Air 2 m Oil =0.80 4 m S = 5 m 3 m Water

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

Q: Both 6-in.-radius wheels roll without slipping on the horizontal sur- face. Knowing that the…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 380 Ib. Dimensions of…

Q: A beam is subjected to equal bending moments of M, = 3000 N-m. The cross-sectional dimensions are b…

Q: Convection heat transfer through the plate is 180 w/m?k. Find convection heat transfer coefficient…

Q: The lap joint is fastened with four 0.83-in.-diameter rivets. The working stress is 14.55 ksi for…

Q: Gears box has (10)Ten speeds, If the minimum and maximum velocity equal to (100)m/min. and…

Q: density, specific volume and specific gravity of

Q: 1. Consider the beam shown in figure 1, derive the equation needed to solve the weight (w) of the…

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 18.86 ksi for…

Q: Question 1: Design a linkage system such that as a float for liquid level measurement moves from 0…

A: Given data- linear range LVDT=3cm = 3×10-2 for 10 bit ADCResolution…

Q: The elements of a floor jack are shown in the figure. If the hydraulic cylinder AB is designed to…

Q: The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

Q: Lecture 6: Balanced Delta Load IBR VeN VRY BR 21.8 IRY 82,V -21.8 IYB VYB.

A: The voltages in the three-stage power framework are delivered by a simultaneous generator . In a…

Q: A0.525 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in.,…

Q: 4. A refrigerant 12 vapour-compression system operates between -10°C and 33°C with saturated liquid…

A: Given data, Temperature range of R-12 VCRS is -10 °C and 33 °C Volumetric efficiency of the…

Q: transmit 50 kW power to a machine. The sheave is 10 inches in diameter and turns at 1200 rpm, while…

Q: Determine the smallest metric hydraulic copper tube size that will carry 4L/min of the following…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A steam power plant uses the ideal Reheat Rankine cycle where the steam enters the high-pressure…

Q: For the plan area shown in the figure, determine the location of the centroid of the shaded area.…

A: Semi circular is cut therefore it is negative area. Square and semicircle cut are in second quadrant…

Q: A 90 cm pulley transmits 75 kW at 750 rpm. The arc of contact between the belt and pulley is 135…

Q: 4) Determine the carburizing time necessary to achieve a carbon concentration of 0.4wt% at a…

A: Solution to first question as per or company policy:

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

A: Given: Width of the wooden boards→w=8 in=0.66 ft Gap between the boards→a=0.6 in=0.05 ft Applied…

Q: 1. Calculate the frictional pressure drop for a 50 % solution of glycerol with a density of 1.1273…

Q: Part (a) Choose the correct free-body diagram for the door. F, Mg Mg F. F. F Mg F Mg F Part (b)…

A: Given data Mass of the door = M = 33 kg Height of the door = h = 2.2 m [ Note : According to…

Q: Explain in brief the difference between passive cooling and active cooling in the context of…

A: The use of fans to minimise the heat generated by computer components is known as active cooling.…

Q: A large manufacturer of air compressors is developing an air-cooled piston model and a water-cooled…

A: For both the models we can see that inital conditions before compression are same Now For the…

Q: A 5 cm long rectangular fin with a cross-section of 2 mmx5 mm is being used on a heated surface.…

Q: Please handwriting make the solution very simple not long 3. [Ch7 – 2] For the first-, second-, and…

A: given details

Q: Locate the centroid (x, y, z) of the wire which is bent in the shape shown. 2 in.

Q: A rolled l-shaped beam is connected to a steel girder by 4-25mm bolts as shown. Determine the…

A: Long before the flanges begin to yield, the web will entirely yield. As a result, the web yielding…

Q: 1. A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 kgm/s. The…

Q: PROBLEM 02: Water entering a pump through an 200mm diameter pipe at 27.6 kPa has a flow rate of 0.1…

Q: a) at the position of the image when the boom is horizontal.

A: Given Data The weigth of the boom is:m=25 kg K=500 kg To find: The cylinder force. Now draw the…

Q: A plastic beam has a cross section with dimensions of a = 2.3 in., b = 8.1 in., d = 4.6 in., and t =…

Q: What are the advantages and disadvantages of the engine lubrication

A: The lubrication system's job is to provide oil to moving parts in order to minimise friction…

Q: 2 litre of petrol weighs 14N. Calculate the specific weight, density, specific volume and specific…

Q: A is 2000 m gas flow line (6-in) and B is 2500 m liquid flow line (4-in) should be onnected both…

Q: A refrigerant 22 refrigerating system is operating with a condenser temperature of 42°C and an…

A: Given that: Refrigerant is R22 Condenser temperature = 42 oC Evaporator temperature = 0 oC (a)…

Q: 6.88 A water jet strikes a cart as shown. After striking the cart, the water is deflected vertically…

Q: The extruded plastic shape will be subjected to an internal shear force of V= 380 Ib. Dimensions of…

Q: (c) A steel rod of 30 mm diameter is 2.8 m long. (i) Find the maximum stress and work done at…

Q: You are the Production Planner of XYZ Food Group Company, your item is Cocoa Powder and the…

A: Given: Forcasted value by the production supervisor: →F=200000 lbs Because→1 lbs=0.453 Kilogram…

Q: Water is the working fluid in an ideal Rankine cycle. Superheated vapor enters the turbine at 8 MPa,…

Q: With a neat sketch explain the working principle of the Scanning Tunneling Microscope.

Q: · For the gas pipeline system shown in figure, calculate the pressure required at A, if Pc=2067 kpa.…

A: The Pipeline Efficiency application assists with guaranteeing stream confirmation, to distinguish…

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

Q: Explain the functions and provide visual presentation of the following auxiliary machinery

A: A boiler, a steam turbine and generator, as well as additional auxiliaries, make up a steam power…

Question

A plate made of mild steel having 10 cm thick, maintaining temperature 250°C. The convection & radiation heat transfer are 2 kw & 1 kw respectively. Find heat conduction through the plate?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must be 204C, what are the required minimum temperature of the base and the heat flow, in watts, into the base? Assume that h=22.7W/m2KandTair=21C.
Temperature of cooling chamber of refrigerator is kept at T1 = 280 K. If the surrounding temperature 1.5 times the temperature of cooling chamber, find the COP of refrigerator. Now, if the surrounding temperature is 1.4 times the cooling chamber temperature, what is new COP?
A constant temperature of -125 C must be maintained in a cryogenic experiment, although it gains 120 W due to heat transfer. What is the smallest motor you would need for a heat pump absorbing heat from the container and rejecting heat to the room at 20 C
3) When a person enters his house, which is completely closed in summer, he sees that the temperature is 34°C. After turning on the air conditioner, the temperature of the house becomes 22 °C within 15 minutes. Since the efficiency coefficient of the air conditioning system is 3.2, a) the electrical power drawn by the system, b) heat dissipated to the environment, and c) Assuming that it works 8 hours a day and the electricity price is 0.6 TL per kWh, find its cost for 4 months. Assume that the entire mass inside the house is equivalent to 1000 kg of air. For air, take Cv = 0.73 kJ/kgK, Cp= 1.0051 kJ/kgK.
Can you show the solutions for this review problem in Thermodynamics 2 8. Water at 2.5 MPa and 200°C is heated at constant temperature up to a quality of 80%. Find (a) the quantity of heat received by the water, (b) the change in internal energy, and (c) the work of a nonflow process. Ans. (a) 2025.7 kJ/kg; (b) 1396.5 kJ/kg; (c) 629.17 kJ/kg
A steel rod of 0.5 cm diameter and 10 m length is stretched 3 cm. Young’s modulus for this steel is 21 kN/cm2 . How much work, in kJ, is required to stretch this rod?
A gas is compressed from an initial volume of 5.75 LL to a final volume of 1.24 LL by an external pressure of 1.00 barbar . During the compression, the gas releases 125 JJ of heat. What is the change in internal energy of the gas?
Water at 2.5 MPa and 200°C is heated at constant temperature up to a quality of 80%. Find (a) the quantity of heat received by the water, (b) the change in internal energy, and (c) the work of a nonflow process. ANS. (a)2025.7 ki/kg; (b) 1396.5 ki/kg; (c) 629.17 ki/kg.
(a) Calculate the rate of heat transfer by radiation from a car radiator at 110°C into a 50.0ºC environment, if the radiator has an emissivity of 0.750 and a 1.20-m^2 surface area. (b) Is this a significant fraction of the heat transfer by an automobile engine? To answer this, assume a horsepower of 200hp (1.5kW) and the efficiency of automobile engines as 25%.
A windmill produces 5 kW and is connected to a battery to charge it. The batterydue to resistive heating loses heat at a constant rate of 2 kW. Find the stored energyin the battery after 2 hours?
The wall of a house, 7 m wide and 6 m high is made from 0.3 m thick brick withk=0.6 W/m.K. The surface temperature on the inside of the wall is 16C and that onthe outside 6C. Find the heat flux through the wall and the total heat loss through it.
Find the change in internal energy in BTU of a 5-lb mass of oxygen when the temperature changes from 100 to 120 deg F. Let c_v=0.157 BTU/(lbm∙°R).