A0.525 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in., and the load applied to each pulley is P = 62 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. Answer: Tmax psi OA Shot on OnePlus 1/3 13 13

A0.525 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in., and the load applied to each pulley is P = 62 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. Answer: Tmax psi OA Shot on OnePlus 1/3 13 13

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

A plain concrete wall (i.e., a wall with no steel reinforcement) rests on a secure foundation and serves as a small dam on a creek (see figure). The height of the wall is h = 6.0 ft and the thickness of the wall is t = 1.0 ft. Determine the maximum tensile and compressive stresses o*!and trt, respectively, at the base of the wall when the water level reaches the top {d = h). Assume plain concrete has weight density ye= 145 lb/ft . Determine the maximum permissible depth dnuxof the water if there is to be no tension in the concrete.
Solve the preceding problem for a column with e = 0.20 in,, L = 12 ft, I = 2L7in4, and E = 30 × 106psi.
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A mild steel shaft transmits 18 kW at 450 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa
A mild steel shaft transmits P is 18 kW at N is 525 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.
The internal loadings at a critical section along the steel drive shaft of a ship are calculated to be a torque of 2300 lb # ft, a bending moment of 1500 lb # ft, and an axial thrust of 2500 lb. If the yield points for tension and shear are sY = 100 ksi and tY = 50 ksi, respectively, determine the required diameter ofthe shaft using the maximum shear stress theory.
A propeller shaft is required to transmit 45 kW power at 500 rpm. It is a hollow shaft having inside diameter 0.6 times the outer diameter. It is made of plain carbon steel and the permissible shear stress is 84 N/mm^2. Determine the inner and outer diameters of the shaft.
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]
Partial answer (a) max and min shear stress = +- 10.6 kpsi (b) vB=-0.0102 in and wB=.0234 in