A plate-bearing test is performed on soil near the surface of a granular stratum in order to determine the modulus of vertical subgrade reaction. The load versus settlement information appears as a straight line on a graphical plot. At a point where the load is 5 tons/ft2, the indicated settlement is 0.5 in. What is the value for the modulus of vertical subgrade reaction?

A plate-bearing test is performed on soil near the surface of a granular stratum in order to determine the modulus of vertical subgrade reaction. The load versus settlement information appears as a straight line on a graphical plot. At a point where the load is 5 tons/ft2, the indicated settlement is 0.5 in. What is the value for the modulus of vertical subgrade reaction?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.22P

See similar textbooks

Similar questions

In the deposit shown in the accompanying figure the groundwater level was originally at the ground surface. The water table was lowered by drainage to a depth of 25 ft., whereupon the degree of saturation of the sand above the lowered water table decreased to 20 percent. 1. What is the effective vertical stress at the mid height of the clay layer before lowering the water table? a. 4350 psf b. 4560 psf c. 3500 psf d. 6400 psf 2. What is the effective vertical stress at the mid height of the clay layer after lowering the water table? a. 4343 psf b. 4557 psf c. 5530 psf d. 6452 psf 3. What is the effective vertical stress at the mid height of the clay layer after lowering the water table to a depth of 50 ft? a. 5580 psf b. 6710 psf c. 3680 psf d. 5860 psf
Subject: Soil Mechanics Please provide a solution and a diagram. A cylindrical sample of soil having a cohesion of 80 kN/m2 and an angle of internal friction of 20°is subjected to a cell pressure of 100 kN/m2. Determine the maximum deviator stress at which the sample will fail in kPa. a. 333 b. 387 c. 255 d. 246
Question 10 In a triaxial test for a cohesive soil sample, when the principal stresses are 452.29 kPa and 62.79 kPa, the soil fails along a plane making an angle of 62.44° with the horizontal. What is the cohesion of the soil in kPa? Round off to two decimal places.
From the given data determine these soil properties and analyse the results, how important are these test data and how can they be integrated within geotechnical design procedures. - If a soil sample tested in a direct shear box of 60 mm by 60 mm and the maximum readings for normal loads of 0.3, 0.5 and 1.0kN were 202, 265 and 511 kN, determine the strength parameters corresponding to effective stress.
Provide a brief description of the term stress path as related to stress conditions in a soil mass.
What is the significance of large or small California Bearing Ratio (C.B.R) value.And why is it that the C.B.R value of a soil sample changes when the sample was soaked with water?
A soil profile is given in Figure 7.18a. The consolidation test in the laboratory was carried out to test a soil sample taken from the center of the soil layer. Interpolated field consolidation curves from experimental results in the laboratory given in Figure 7.18b. Calculate the amount of settlement that occurs as a result of primary consolidation if an embankment (surcharge) of 50 kN/m² is placed on the ground surface.
Q: Considering the following steps write a detailed note on how you develop a model in Plaxis. Creation of geometry Standard fixities Input soil model Generation of mesh Initial conditions
Relating to soil deposits, provide a definition of subsurface effective stress and total stress, and explain the relationship between the two.
Geotechnical Engineering The following are the results of a standard penetration test in sand. Estimate the soil friction angle at the 3.0 meter depths given N60 =7 . Note that the water table was not observed within a depth of 12 m below the ground surface. Assume that the average unit weight of sand is 15.5 kN/m3 and Pa = 100 kN/m2. a. 44.6 b. 37.6 c. 38.9 d. 34.4
Define a note on Stress distribution in soils ?
Discuss how the analysis of sediment can be used in environmental reconstructions.