(a) Plot the data as impact energy versus temperature. (b) Determine a ductile-to-brittle transition temperature as that temperature corresponding to the average of the maximum and minimum impact energies. (c) Determine a ductile-to-brittle transition temperature as that temperature at which the impact energy is 80 J.

(a) Plot the data as impact energy versus temperature. (b) Determine a ductile-to-brittle transition temperature as that temperature corresponding to the average of the maximum and minimum impact energies. (c) Determine a ductile-to-brittle transition temperature as that temperature at which the impact energy is 80 J.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: Kindly give me both right answers. A) Did the ductile materials (annealed and aluminium) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of ductile materials in compression vs. tension? B) Did the brittle material (quenched) react differently to the two different testing methods (hardness test vs. tensile test)? What does this say about the behaviour of brittle materials in compression vs. tension? （Three to five sentence answers are good）（engineering material)
Tensile and fully reversed loading fatigue tests were conducted for a certain steel alloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa, respectively. If a rod of this material supply were subjected to a static stress of 600 MPa and oscillating stresses whose total range was 700 MPa, would you expect the rod to fail by fatigue processes? Hint: You may want to plot a diagram to aid in presenting your answer.
Answer the following questions briefly,a) Compression tests are generally performed on brittle materials-why? b) How a cast iron specimen fails under compression load? c) Define secant modulus? d) Why alignment of the specimen is is important in compression test? e) Which is the IS code used for compression test on metals?
Can the maximum normal stress theory or Mohr’s failure criterion be used in practice to predict the failure of a brittle material?
⦁ Answer the following questions about the Ductile-to-Brittle Transition Temperature (DBTT).Explain the three main factors in the change in properties of a material from ductile to brittle.
Is the maximum normal stress theory useful to predict the accurate failure of brittle material?
For an 18-8 Mo stainless steel (Figure 1) subjected to creep, you have been asked to a) predict the time to rupture for a component that is subjected to a stress of 100 MPa at 873 K. b) When the temperature is 500 oC (723 K), what is the maximum allowable stress level for a rupture lifetime of 5 years? 20 years?
A low-carbon steel alloy was loaded in tension until just after yielding took place. A few Luders bands were visible on the surface. The bar can either be reloaded (a) immediately, (b) after a brief and moderate temperature aging treatment, or (c) after several weeks without any exposure to elevated temperature. In each of the three cases, how is the yield strength of the reloaded bar likely to compare to that of the original test?
9.23 After consultation of other references, write a brief report on one or two nondestructive test techniques that are used to detect and measure internal and/or surface flaws in metal alloys. 9.28 Briefly explain why BCC and HCP metal alloys may experience a ductile-to-brittle 00 transition with decreasing temperature, Bill whereas FCC alloys do not experience such a transition.
When does the mean stress level affect fatigue crack propagation rates in metal alloys?
Under what conditions may a ductile material undergo a brittle fracture?
5. A low-nickel steel in the heat-treated condition had an 'engineering' tensile strength of 708 N/mm2. The reduction in area of cross-section at the fracture was 44%. What was the true tensile strength of the steel? (2.31)