A pneumatic power system will usually have a return line  a. True b. False

Q: Name at least five different materials that are used in a refrigerator.

A: List of five materials which are used in a refrigerator are:   1. Aluminum  2. A metal sheet  3.…

Q: Diagram a circuit that would allow for the manual lowering of a load on a cylinder using a simple…

A:

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: Which device is not an actuator? O a. Thermocouple O b. Servo motor O C. Engine O d. Compressor

A: An actuator is a device that is responsible for the movement of any part in the system. It also…

Q: Describe the differences between an overrunningalternator pulley and an alternator decoupler pulley

A: The overrunning alternator pulley is an evolution of the alternator's fixed belt pulley. It…

Q: * The unit of measurement for torque is

A:

Q: Describe the voltage needed by an accelerator between accelerating tubes.

A: In this problem, it is asking about the voltage that is needed by an accelerator between…

Q: The shaking forces acting on an engine is mainly due to

A: The shaking forces acting on an engine is mainly due to  Answer: Crank

Q: Why solenoid is used in almost all industrial applications, draw a schematic diagram…

A: Answer : Solenoid :- It is a hollow cylindrical coil of wire acting as a magnet while when current…

Q: controls on/off of the motor, when the air compressor tank reaches the specified bar.

A: Compressed and filtered air enters the tank after coming out of the Air compressor

Q: FAD Fan -60m- 40 m 40m Figure Q2(b)

A:

Q: Among the following, which drive is least reliable in power transmission. O Gear drive O Rope drive

A: The transfer of energy from its place of generation to a place where it is used to do useful work is…

Q: What is called to "USE OF TEMPERATURE INTERVAL OR DIFFERENCE EQUAL TO THE KELVIN

A: The link between the Celsius and Kelvin scales can be expressed mathematically as follows: K = 273 +…

Q: B2. Explain the function of Thermocouple with neat diagram and mention its advantages.

A: The thermocouple is a thermoelectric device that is used for temperature sensing. It is based on See…

Q: b.has air-conditioning and is an automatic.c.has air-conditioning or is an automatic.d.has…

A: Air conditioning :- It is defined as the simultaneous control of temperature of air, velocity of…

Q: Which of the following is NOT a unit of pressure? Pa bar N/m2 ON

A: Pressure: The pressure is defined as the ratio of force per unit area. The unit of the pressure is…

Q: Circuit Diagram and Procedure and Observation Double acting cylinder circuit for hydraulic system…

A: Double-acting cylinder circuit for a hydraulic system using 5/2 double solenoid operated with spring…

Q: Draw a neat diagram and explain in detail about any one type of rotary compressor.

A: "Rotary Vane compressor" is one kind of rotary compressor. It  has sliding vanes  which are fit over…

Q: Discuss why Inverter type generators are much less noiser ?

A: Inverter generator is type of generator with electronic upgrade. This is used to adjust the engine…

Q: e power output from

A: Need to calculate the power output.

Q: AC det D The balance condition for AC bridges is: Select one: O 1.7,Z,-Z,Z, O 2. R,R,=R,R3 O 3.…

A:

Q: A load is an electrical device that__________.a. produces electricityb. directs the flow of…

A: Load  is referred any device/equipment connected to electric circuit which consumes electricity and…

Q: is a device which converts fluid power to linear or rotary mechanical power. Select one: O a. Valve…

A: Answer:- Option (B) correct.  Cylinder

Q: Piezometers measure ..pressure only

A: Subject : fluid mechanics

Q: What is stand for AFUE and explain its efficiency system

A: AFUE stands for Annual Fuel Utilization Efficiency.

Q: 2. Draw and Explain the Circuit diagram for holding the cylinder of double acting cylinder in the…

A: Circuit diagram for holding the cylinder of double acting cylinder in the fully extended position…

Q: Find tension in AC and W? 6 30 10 Ibs A O w-18 Ibs, TAC=20.1 lbs O w-18.95 lbs, TAC=21.91 lbs O w=20…

A: Given  To determine  Tension in AC and weight W

Q: 3. (a) Define and classify steam generator. (b) Show with neat sketch the pressure distribution of…

A: A steam generator is used to generate steam at a specified rate and specified pressure and…

Q: An oil leak at the bellows of a rack and pinion could be caused by ______.

A: As per given question  What is the cause of Oli leak at bellows of a rack and pinion

Q: Vertical configuration for hydraulic power units are usually used for applications which require…

A: The given statement is True.

Q: V- belt 40kw 80rad/sec 20rad/sec D2 800mm

A:

Q: A counter balance valve is not used for always flow retardation continuously, and resists its flow…

A: true

Q: of the following is considered elerator" in an automobile? * of them. s pedal ering wheel ke pedal n…

A:

Q: What is a standpipe?

A:

Q: A shunt generator is running at 1000 rpm. If flux is reduced by half, then what is * ?the new speed…

A: In shunt generator the flux is directly proportional to the speed.

Q: If an actuator fails to move, name five possible causes.f an actuator has slow or erratic motion,…

A: Actuator is a component of a machine which capable in moving in a controlled mechanism.It consist of…

Q: In a DC machine, armature shaft is generally supported at the both ends by Brushes Bearings Yoke…

A: The DC machine is given to support the armatire shaft.

Q: The fluid leaves the impeller with more velocity head Select one: True False

A:

Q: Find tension in AC and W ? 60 10 lbs A w

A:

Q: The different descriptions for fluid power conductors (lines). The ___________ line is used to…

A: The actuator is a device that is used to convert control signal to mechanism motion. Actuators use…

Q: The energy gained due to friction in bearings is called Mechanical efficiency. Select one: True…

A: Correct answer is given below

Q: he different descriptions for fluid power conductors (lines). The ___________ lines are connected to…

A: The actuator is a device that is used to convert control signal to mechanism motion. Actuators are…

Q: In a DCV, this part is located on either or both sides of the spool to position it in the middle…

A: DCV is the directional control value that performs 3 functions, 1. Allow the fluid flow, 2. Change…

Q: Forcesin Cable BA d ch-7 lom 2om

A: Given: W=100 kg

Q: Circuit Diagram and Procedure

A:

Q: A So Find tension in AC and BC Hoola

A:

Q: Draw the circuit diagram of single acting cylinder for pneumatic system using (3/2) 3-ports And 2…

A: The diagram of the circuit of single acting cylinder for pneumatic system using (3/2) 3-ports given…

Q: Construct a circuit drawing of a hydraulic dump lift using an open center circuit.

A: To construct an open center circuit of a hydraulic pump

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.