A pole is at an angle with a force F applied at a different angle at the end (as shown in figure withparameters defined in table). What are the magnitudes of the components of the force parallel andperpendicular to the pole?zFNG SA2021 Cathy ZupkeparametervalueunitsF400lb4ftL2La2ftft4055The magnitude of the component of F parallel to pole=lb.The magnitude of the component of F perpendicular to pole= =lb.

Answered: Image /qna-images/answer/5d8da0da-a004-4932-bc2b-0485b80d7ecb.jpg

A pole is at an angle with a force F applied at a different angle at the end (as shown in figure with parameters defined in table). What are the magnitudes of the components of the force parallel and perpendicular to the pole? 2021 Cathy Zupke parameter value units 400 lb L L2 LA 4 ft 2 ft 2 ft 40 55 The magnitude of the component of F parallel to pole= The magnitude of the component of F perpendicular to pole= lb. lb.

A pole is at an angle with a force F applied at a different angle at the end (as shown in figure with parameters defined in table). What are the magnitudes of the components of the force parallel and perpendicular to the pole? 2021 Cathy Zupke parameter value units 400 lb L L2 LA 4 ft 2 ft 2 ft 40 55 The magnitude of the component of F parallel to pole= The magnitude of the component of F perpendicular to pole= lb. lb.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 25P

See similar textbooks

Similar questions

Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301Nm. Find the deflection of the beam in millimetres if the beam is under a uniform load of 86N/m and is supported with simple supports at both ends. Fill out the table below with your answers. x�-coordinate Deflection (mm��) x=0.22 y(x)= x=1.38 y(x) = x=2.05 y(x) = x=2.98 y(x) = x=3.58 y(x) = Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within ±0.0005±0.0005 of the correct answer to be considered correct.
A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to be 1500m. The tape was Standardized under a pull of 6.75kg but after the line was measured, it was Found that the pull actually used during the measurement was = 7.75 kg. what Was the true length of the line if the tape was standardized & used on the flat? Take young modulus, E = 2,000,000 kg/cm²
4. This figure shows a cantilever beam that is subject to a point load and a moment. What is the vertical displacement at the tip of the beam? Assume E = 200 GPa and / = 1560 X 10° mm%. A. 58.7 mm B. 68.9 mm C. 89.0 mm D. 100 mm
two pulleys connected by a cord with a speed of 4m/s is shown below. The acceleration of A is 300 m/s^2. What is the acceleration of B at this same instant?
A teacher asks her pupils to draw a circle with some compasses they have been givenThe pdf of the radii is given by f(r) = r/4; 1
! use the given datas on solving ! refer image when needed. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E=2*10^ 6 kg/cm^ 2 and the unit weight y of the steel to be 7.9*10^ -3 kg/cm^ 3 . a) Determine the cross-sectional area of the tape. Hint: y = W/V b) Determine the correction due to pull for one tape length. c) Determine the total correction due to pull. d) Determine the corrected distance.
*refer image for correct data Pls solve all questions for full answers. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E=2*10^ 6 kg/cm^ 2 and the unit weight y of the steel to be 7.9*10^ -3 kg/cm^ 3 . a) Determine the cross-sectional area of the tape. Hint: y = W/V b) Determine the correction due to pull for one tape length. c) Determine the total correction due to pull. d) Determine the corrected distance.
Suppose we have a uniform beam that is 3.40metres long has a flexural rigidity of 31915N Find the deflection of the beam in millimetres if the beam is under a uniform load of 24Nmand is supported with simple supports at both ends. Fill out the table below with your answers. x�-coordinate Deflection (mm��) x=0.14 y(x)�(�) = x=1.12 y(x)�(�) = x=1.80 y(x)�(�) = x=2.65 y(x)�(�) = x=3.06 y(x)�(�) = Enter as many decimal places as your calculator allows (8 to 10). Your answer must be within ±0.0005±0.0005 of the correct answer to be considered correct.
Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the second moment of area (statical moment of area), Q, of the diamond cross- section at the neutral axis? (in mm3) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation.
GIVEN THE ILLUSTRATION IN THE PICTURE, IF THE HANDLE IS SUBJECTED TO FORCE= 70LB, WHAT COULD BE THE MOMENT OF THIS FORCE ABOUT IN POINT A? CHOICES ARE: A. 1141 B. 829 C. 674 D. 985 E 518
The figure (Figure 1) shows a model of a crane that may be mounted on a truck.A rigid uniform horizontal bar of mass m1m1m_1 = 90.0 kgkg and length LLL = 5.20 mm is supported by two vertical massless strings. String A is attached at a distance ddd = 1.20 mm from the left end of the bar and is connected to the top plate. String B is attached to the left end of the bar and is connected to the floor. An object of mass m2m2m_2 = 3500 kgkg is supported by the crane at a distance xxx = 5.00 mm from the left end of the bar. Throughout this problem, positive torque is counterclockwise and use 9.80 m/s2m/s2 for the magnitude of the acceleration due to gravity. Find TA, the tension in string A. Find TB, the magnitude of the tension in string B.
A 50 m steel tape measured 50.0250 m when standardized fully supported under a 90-newton pull at a temperature of 20°C. The tape weighed 12N and had a cross-sectional area of 0.028 cm^2. What is the true length of the recorded distance AB for the following condition? (K= 0.0000116/°C, modulus of Elasticity =2.1x10^7).Recorded distance: 215.095 mAverage temperature: 12°CMeans of support: SuspendedTension: 120 NElevation difference per 100 m: 2.5mRound off the final answers to the nearest hundred thousandths (five decimal places) and indicate if the answer is positive or negative. 1. Determine the temperature correction for the entire length of the distance measured. 2. Give the correction for the absolute length of the tape, accounting the full length it measured. 3. Determine the sag correction for one tape length. 4. Determine the pull correction for the entire length of the distance measured. 5. Compute for the slope correction for the entire length of the distance measured.