A pond located at 60 m height is requiring a pump to deliver water at a capacity of 0.05 m³/s from water reservoir shown in the following Figure 3. The water is delivered nsing a commercial cast iron pipe with pipe surtface roughness, ɛ of 0.26 mm having a diameter of 0.2 m at a length of 150 m K = 1.0 Pump K = 1.5 H K = 5.0 K = 0.8 Figure 3: The Schematic Pipe Layout of a water flow system From the data given, (a) Analyze the overall system by identifying the flow regime of the overall pipe layout. (b) Calculate the overall losses incurred by the pipe system. c) Obtain the head of pump (hp) required to accommodaté the requirement of the demand.

A pond located at 60 m height is requiring a pump to deliver water at a capacity of 0.05 m³/s from water reservoir shown in the following Figure 3. The water is delivered nsing a commercial cast iron pipe with pipe surtface roughness, ɛ of 0.26 mm having a diameter of 0.2 m at a length of 150 m K = 1.0 Pump K = 1.5 H K = 5.0 K = 0.8 Figure 3: The Schematic Pipe Layout of a water flow system From the data given, (a) Analyze the overall system by identifying the flow regime of the overall pipe layout. (b) Calculate the overall losses incurred by the pipe system. c) Obtain the head of pump (hp) required to accommodaté the requirement of the demand.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump is used to pump the water at its temperature in a reservoir with the free water surface located 2 m above the center of the pump inlet to the atmosphere. Piping system in 5ng from tank to pump; It consists of 3 galvanized iron pipes with an internal diameter of 20 cm and an average internal roughness of 0.15 mm. Local ancillary elements above the piping system are years; Sharp edged inlet (Kg-0,85), flanged smooth 3 pieces 90 ° bend -0,3 each thousand and one flanged full open globe valve (KK-8). Find the net positive charge on the usable suction since the minimum volumetric flow is 30 L / s that can be mpaed without cavitation. Evaporation pressure for water at 25 ° temperature: 3.169 kPa) (Standard atmospheric pressure: 101.3 kPa) -997 kg / m3 (-1.05) (dynamic viscosity of water at 25 ° temperature: 8.91.10-kg / ms)
The parallel galvanized iron pipe system of Fig. delivers water at 20°C with a total flow rate of 0.036 m3/s.If the pump is wide open and not running, with a loss coefficient K = 1.5, determine (a) the flow rate in each pipe and(b) the overall pressure drop.
Can you use the friction factor for turbulent flow in a smooth circular tube to predict the fiction factor in an internally finned tube by using the hydraulic diameter?
Water at 10oC is to flow from reservoir A to reservoir B through a cast-iron pipe of length 20 m at a rate of Q=0.0015 m3/s as shown in Figure. The system contains a sharp-edged entrance and six regular threaded 90° elbows. Determine the pipe diameter needed.
Water at 20°C is to be pumped from one tank (ZA=5 m) to another tank at a higher elevation (ZB=13 m) through two 36 m long pipes connected in parallel, as shown in the figure. . The pipes are made of commercial steel, and the diameters of the two pipes are 4 and 8 cm. Water will be pumped via a 70 percent efficient motor-pump coupling that extracts 8 kW of electrical power during operation. Minor losses and head loss in the pipes connecting the pipe joints parallel to the two tanks are considered negligible. Determine the total flow rate between the reservoirs and the flow rate through each of the parallel pipes. Hypothesis: 1.The flow is stationary and incompressible. 2. The input elects are negligible and therefore the flow is fully developed. 3. The elevation of deposits remains constant. 4. Minor losses and head loss in pipes other than parallel pipes are said to be negligible. 5. The flows through both pipes are turbulent (to be verified).
Determine the Reynold's Number and flow regime of an bil flowing through a 450-mm diameter pipe, if the flow rate is 0.40 m³/s. Note: Hoil = 0.025 Pa's and Scoil = 0.86).
is friction factor inversely proportional to the Reynold’s number in case of laminar flow in circular pipes?
A 250 mm diameter and 3 km long straight pipe connects two reservoirs of water surface elevations 135.00 m and 60.00 m. A 1.5 km long, 300 mm diameter pipe is laid parallel to 250 mm diameter pipe from its mid-point to the lower reservoir. Neglecting minor losses and assuming friction factor as 0.02 for both the pipes. Find the original discharge and the increased discharge
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
In large buildings, hot water from the water tank is continously recurculated in a loop to avoid long waits for hot water while cold water drains out of the pipe first. A certain recirculating loop is 30 m long and uses 22 mm diameter polyethene pipes which have a surface roughness of 0.0005 mm. The loop contains six 90 degree elbows, each with a local loss coefficient of 0.3. If the average flow velocity is 2.5 m s1, determine the required power input for the recirculating pump if its efficiency is 80%.
In a water Transfer installation, from the storage tank to the consumption tank, a pump is to be installed to circulate a flow rate of 60 lt/s. The 380 meter long Pipe is Made of cast iron of 150 mm diameter and consist of a check valve, a gate valve and 3 commercial elbows of medium Radius.The consumir tank is pressurized to 3.5 Kgf/cm2 gauge pressure.Determine the driving power of the KW pump if it's efficiency is 73%. Additional data, head loss factors: - check valve - Open gate valve Kv= 0,19 -commercial elbow of average Radius Kc= 0,75, per elbow. - storage pond outlet sharp angles Ks = 0,5 - inlet to consumption pond Le = 1 - Pipe friction factor f = 0,029