A power plant uses steam flowing at 75kg/s to perform power cycle. Both the turbine and the pump operate adiabatically and without irreversibilities. a) find quality at the turbine exit b) find mass flow rate (kg/s) of cooling water through the condenser c) find efficiency of the cycle d) plot the cycle on a T-s diagram, indicate the saturation curve and each state of the working fluid.

A power plant uses steam flowing at 75kg/s to perform power cycle. Both the turbine and the pump operate adiabatically and without irreversibilities. a) find quality at the turbine exit b) find mass flow rate (kg/s) of cooling water through the condenser c) find efficiency of the cycle d) plot the cycle on a T-s diagram, indicate the saturation curve and each state of the working fluid.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter46: Room Air Conditioners

Section: Chapter Questions

Problem 15RQ

See similar textbooks

Similar questions

N2O expands isentropically through a duct from p1 =200 kPa and T1 = 250°C to a downstream section wherep2 = 26 kPa and V2 = 594 m/s. Compute (a) T2; (b) Ma2;(c) To; (d ) po; (e) V1; and (f ) Ma1.
A dry gas well equipped 30 MMcfd with 85psig tubing pressure must be compressed to 300 psig for sales by centrifugal compressor design What is the amount of actual power required to perform this job, estimate the minimum number of compression stages required for optimum compression efficiency? Additional data nsty = 0.069 cuft , suction temperature 85 K = 1.2 . theoretical speed N - 12200 rpm average deviation factor -0.85atmospheric pressure (assumed xd)=14.71 psia
An air compressor is to compress 28.707 m^3/min from 130.588 kPa to 225.248 kPa. Assuming condition is ideal, and n=1.3 What will be the % increase due to 2 staging Answer in % and round off to 1 decimal places (e.g. 4.3%)
Answer this ASAP plz Air enters a pipe with a diameter of 3 cm and a length of 17 m with a speed of V1 = 75 m/s, pressure P₁ = 600 kPa and T₁ = 60 °C and a friction factor of 0.025. Count: a. V2, P2, T2 and po2 at the end of the pipe. b. What is the additional length of the pipe that causes the outflow to be sonic.
Q . It is proposed to pump 8,000 kg/h of toluene at 114 oC and 1.1 atm abs pressure from the reboilerof a distillation tower to a second distillation unit without cooling the toluene before it enters thepump. If the friction loss in the line between the reboiler and pump is 7 kN/m2 and the density oftoluene is 866 kg/m3 . How far above the pump must the liquid level in the reboiler be maintained togive a net positive suction head of 3.5 m? Calculate the power required to drive the pump if the pumpis to elevate the toluene 10 m. The pressure in the second unit is atmospheric and the friction loss inthe discharge line is 35 kN/m2 . The velocity in the pump discharge line is 4 m/s.
A boiler requires 100 000 m3/hr of standard air. The mechanical efficiency of fan to be installed is 70%. Determine the size of driving motor needed assuming fan can deliver a pressure head of 160mm of water and outlet velocity of 20m/s. ANSWER: 60 kw
Air is kept in a tank at pressure Po = 689 KPa abs and temperature To = 17°C. If one allows the air to issue out in a one-dimensional isentropic flow, the flow per unit area at the exit of the nozzle where P = 101.325 KPa is Blank 1 kg/m2-s. For air, Use R = 287 J/kg-K and Mol. Wt. = 29.1 *Express your answers in whole significant figure without decimal value and without unit*
fan ventilates at 500rev/min, the airflow is measyured at 150cubic meters/second. the ventilation pressure is 0.40kPa while thepressure along fan is0.85kPa.the mine requires 100cubic meters/second of air flow on an off day.efficiency=0.75. 1.new slow down speed required on an off day 2. Annual savings in electricty if the costs is R0.63/kWh 3. Comment on any savings in the maximum demand. 4. methods for reduction of speed on off-day.
Air fl ows adiabatically in a 3-cm-diameter duct, withf 5 0.018. At the entrance, T1 = 323 K, p1 =200 kPa, andV1 = 72 m/s. (a) What is the mass fl ow? (b) For what tubelength will the fl ow choke? (c) If the tube length is increasedto 112 m, with the same inlet pressure and temperature,what will be the new mass fl ow?
The initial condition of air in an air compressor is 100 Kpa and 25 degrees Celcius and discharges air at 725 Kpa. The bore and stroke are 276 mm and 186 mm respectively with 3 % clearance runningat 6 rev/sec.1.1 Illustrate the PV diagram 1.2 Discuss the processes in PV diagram 1.3 Solve the volumetric effieciency
Assuming the clearance is negligible for a single stage compressor with the followingdata.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1. What is the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1.25? 2. What is the delivery temperature of air for an isentropic compression process in Kelvin to 1 decimal place? 3. What is the power input to the compressor in kW to 3 decimal places if the compression reversible isothermal?
.........TheGaugePressure 0f the air in an aut0m0bile tire is 25psi, and assuming the ambient atm0sphericPressure is38psi. Express the_abs0lute_pressure_in the tire in bars.