A power system consists of 4 buses as shown in Figure Q1. Generators are connected at buses 1 and 3 reactances of which are j0.2 and j0.1, respectively. The transmission lines are connected between buses 1-2, 1-4, 2-3 and 3-4 and have reactances j0.25, j0.5, j0.4 and j0.1, respectively. Find the bus admittance matrix.

A power system consists of 4 buses as shown in Figure Q1. Generators are connected at buses 1 and 3 reactances of which are j0.2 and j0.1, respectively. The transmission lines are connected between buses 1-2, 1-4, 2-3 and 3-4 and have reactances j0.25, j0.5, j0.4 and j0.1, respectively. Find the bus admittance matrix.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.9P

See similar textbooks

Similar questions

While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
A two-area system connected by tie-line has the following parameters on a 1000 MVA common base Area The units are operating in parallel at the nominal frequency of 50 Hz. A load change of 200 MW occurs in area 1. Determine the new steady state frequency and the change in the tie-line flow?
a) How many MVAr of shunt capacitors are required to increase the power factor on a 10 MVA load from 0.85 to 0.9 lagging? b) How many MVAr of shunt capacitors are required to increase the power factor on a 10 MVA load from 0.90- to 0.95 lagging? c) Which requires more reactive power, improving a low power-factor load (case a) or a high power-factor load (case b)?
Explain the significance of load flow analysis in power systems. How does it help in determining the steady-state operating conditions of a power network?
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
Explain the concept of load flow analysis in power systems. How is it used to determine the steady-state operating conditions of a power network?
5.65 Open PowerWorld Simulator case Example 5_10 with the series capacitive compensation at both ends of the line in service. Graph the load bus voltage as a function of load real power (assuming unity power factor at the load). What is the maximum amount of real power that can be transferred to the load at unity power factor if the load voltage is always greater than 0.85 per unit?
An AC generator having an internal resistance of 2 ?? is connected to an LCR circuit in series as shown in the figure. If the generator supplies an electromotive force, ? = 282 ??? (100??) volt, calculate:a) the impedance of the circuitb) the rms value of the current in the circuitc) the voltage drop across L, C and R
a short three phase transmission line connected to 33kv 50 hertz generating station at starting and is required to supply a load of 10 MW at pointed start lagging power factor at 30 KV addresses in that is the minimum transmission efficiency is to be determined96% estimate the per face value of resistance and inductance of a line