A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 45 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m

A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 45 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What size pipe will deliver 90 gpm of oil at 40 deg F given the viscosity 6.55 x10-5 ft/s. Assume laminar flow. a. 2.13 ft b. 1.89 ft c. 1.95 ft d. 2.05 ft
Three pipes connected in series with lengths L1 = L2 = L3 = 300 m and diameters D1 = 75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 50 mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Haaland and Darcy-Weisbach Formula, determine the following: a. Which pipe has the highest Renoylds Number? b. Which pipe is the smoothest? c. Compute the total head loss
a= 4.9m b=36.3 kN/m c= 21.8 kN d= 28.1 kN/m Complete solution need ASAP. THANK YOU.
Include a free body diagram. A 12′′ pipe is being tested to evaluate the lost head. When the flow of water is 6.31 cfs, the pressure at point A in the pipe is 40 psi. A differential gage is attached to the pipe at A and at a point Bdownstream that is 10 ft higher than A. The deflection of mercury in the gage is 3.33 ft, indicating a greater pressure at A. What is the lost head A to 5?
A vertical triangular plate has a base of 1m and depth of 2.1m. The base is horizontal and flushed with the water surface. What is the distance of force of water below the centroid of the plate? Show complete solution. need ASAP. Thank you.
8.A standard steel tube, 1.5 25-mm OD x 1.5-mm wall (Appendix G.2), is carrying 19.7 L/min of oil. Calculate the velocity of flow.
3. Two concrete pipes are connected in seriesThe flow rate of water through the pipes is 0.14 m/s with a total friction loss of 14,10 m for both pipes. Each pipe has a length of 300 m. If one pipe has a diameter of 300 mm, what is the diameter of the other one? Neglect minor losses Use dot f = 0.021
The air-oil-water system is shown in figure. If gage A reads 17psi absolute andgage B reads 2.2psi less than C, compute the unit weight of oil in pcf (pounds percubic feet). Use unit weight of air equal to 0.76pcf. Also compute the gauge reading point at C.
Oil is being transported at a rate of 20gal/min through a 2-in schedule 40 steel pipe (ID = 2.067in). The oil has a viscosity of 20cP and a specific gravity of 0.85. The line is slanted, and the static pressure at one point in the line is 45 psig. Calculate the static pressure (in psig) at a location in the line 200 feet further along flow direction and 50 feet lower in elevation.
Compute the head loss (in meters) in 2000 m of horizontal, steel pipe with nominal pipe size of 300 mm and SCH 30. The pipe is carrying water with an average velocity of 1.88 m/s. Take water at 20°C to have a viscosity of 1.00E-3 Pa-s and density of 1000 kg/(m^3). Take the roughness of steel pipe to be 0.048 mm. Round your answer to 2 decimal places.
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
Problem :3 only (category: friction factor, FE prep): Air at 1 atm and 10°C flows in a 4 cm diameter glass pipe (roughness of 0) at a velocity of 7 m/s. Find the friction factor. Calculate the head loss over a 2 m length of pipe. Air at 1 atm and 10°C has kinematic viscosity of 1.087 x 10-5