The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10 cm at sections I and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at sec- tion 1 is 39.24 N/cm², find the intensity of pressure at section 2. L 6 m/ DATUM LINE 4m D₂ = 10 cm

The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10 cm at sections I and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at sec- tion 1 is 39.24 N/cm², find the intensity of pressure at section 2. L 6 m/ DATUM LINE 4m D₂ = 10 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows down a vertical pipe whose diameter increases suddenly from 175 mm to 350 mm. The discharge in the pipe is 85 lps. The pressure 0.6m above the enlargement section is 275 kPa. Find the pressure at a section 0.6 m below the enlargement section.
Points A and B are 4.8km apart along a 60cm new cast iron pipe carrying water. A is 10cm higher than B. If the pressure at A is 140kPa higher than B How much will the flow be? use C = 110
Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.
A main pipe distributing water has a diameter of 158 mm and is distributed into three outlets. Thefirst outlet has a velocity rate of 10m/s and a diameter of 50mm. The second outlet has a velocity rate of11m/s and a diameter of 75mm. The third outlet has a flow rate of 0.265619 m^3/s moving at avelocity of 15m/s. if the pressure head in the larger diameter part is 28 ft. a) determine thepressure head at the smaller diameter. b) what is the velocity head of the larger pipe? c) what is the velocityhead of the smaller pipe? d) What is the total head in the system?
The rectangular bin with an inclined gate AB is filled with water to the depth shown. Determine the location in meters along with the inclination of the center of pressure from the water surface when the total pressure is acting on gate AB x=0.82 a=2.02 m b=30 degrees asap 15 mins
A vertical conical pipe has diameter 1.5 ft at the top and 3.0 ft at the bottom and 60 ft long. The friction loss is 10 ft for flow in either direction when the velocity at the top is 30 fps and the pressure head there is 6.5 ft of water. Find the pressure head in ft at the bottom when the flow is upward. a.69.6 b.58.0 c.89.6 d.46.0
Water flows through a pipe at 5L/s as shown in the figure. The gage pressure of 150.5 kPa,118.03 kPa, and 115.87 kPa are meassured for p1,p2 and p3, respectively. A.What is the head loss between 1 and 2 Choices: 3.31m,3.81m,5.24m,4.25m B.what is the headloss between 2 and 3 Choices: 7.8m,7.7m,7.9m,8.0m C.What is the distance between 1 and 2 if the friction factor 0.02? Choices: 25m,15m,20m,30m
Water at 20°C exits the atmosphere through the split nozzle as shown in Figure-5. The duct areas are ?1=0.02 m2 and ?2=?3=0.008 m2. If the gauge pressure at the inlet is equal to 9786 kPa and the flow rate is ?.2=?.3=200 m3/h, compute the force acting on the flange.
A 30-cm by 15-cm Venturi meter is mounted on a vertical pipe with the flowupward. One hundred twenty-six (126) liters per second of oil (s.g. = 0.80)flows through the pipe. The throat section is 15cm above the upstreamPage 2 of 3section. If Cv=0.957, what is the difference in pressure between the inlet andthe throat?
Water flows from a large reservoir at the rate of 0.0137 m3/s through the system shown in the Fig. below. Calculate the pressure at B. NB: Use f = 0.017 (friction factor) and fT = 0.010 in zone of complete turbulence. Hint: Include minor losses, assume K = 1.0 for the inlet or entrance and use the applicable appendix at the back of the textbook to obtain the pipe parameters.
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 45 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m.