A pump is used for pumping water from lake at height of 100 m consuming power of 60 kW. Inlet pipe and exit pipe diameters are 150 mm and 180 mm respectively. The atmospheric temperature is 293 K. Determine the temperature of water at exit of pipe. Take specific heat of water as 4.18 ??/??. ?

A pump is used for pumping water from lake at height of 100 m consuming power of 60 kW. Inlet pipe and exit pipe diameters are 150 mm and 180 mm respectively. The atmospheric temperature is 293 K. Determine the temperature of water at exit of pipe. Take specific heat of water as 4.18 ??/??. ?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.40P

See similar textbooks

Related questions

Q: Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser…

Q: Water at T, = 24°C is heated to T, = 74°C by passing it through an alternating 2. %3D array of…

Q: A student living in a 3-m X 4-m X 4-m dormitory room turns on her 100-W fan before she leaves the…

A: Using the properties of air R=287 J/Kg-KCp=1.005 KJ/Kg-KCv=0.717 kj/Kg-K Given Data Volume of the…

Q: The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that…

Q: A counter-flow bank of boiler tubes has a total area of 900 sq ft and its overall efficiency of heat…

Q: Calculate the amount of energy required in BTU to heat the air in a 10°F house 30 by 50 by 40 ft and…

Q: O heat Source 140°C %3D Civen: composite wall (3 layers) poy unethane board Corerete rock w ool (15…

A: given; ⇒T1=1400c=413K⇒concrete temeperature (Tc)=320c=305K⇒length(l1)=15cm=0.15m⇒conductivity…

Q: A closed, expandable system like that shown below is operated in an adiabatic manner. First, 15,000…

Q: "Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285…

A: For piston, Diameter (d) = 30 mm = 0.03 m For the metal can in the hot reservoir, Height of the…

Q: Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser…

Q: (ii) Consider the process of baking potatoes in a conventional oven. Can the hot air in the oven be…

Q: "Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285…

A: Given, diameter of the combustion chamber, d =30mm = 0.03 m Volume of the metal can cylinder =…

Q: Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1525 kJ is…

Q: 1. A heat engine is supplied heat at the rate of 1700 kJ/min and gives an output of 9 kw. Determine…

Q: Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1525 kJ is…

Q: Concentrating solar power plants are frequently located in desert areas where they can collect a lot…

Q: Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser…

Q: Consider the heating of water in a pan on a top of a range. If 24 kJ of heat is transferred to the…

Q: The interior of a refrigerator has a surface area of 6.2 m2. It is insulated by a 2 cm thick…

A: find the power required to run the compressor.

Q: A fuel oil of 21 deg API (density = 934 kg/m³) is to be heated in a heater and has the following…

Q: A solar panel 1.5 square meter receives heat energy from the sun at 2.2 KW/m². It is used to heat…

Q: The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that…

A: Given data as per the question Refrigeration capacity = 15 tons evaporator temperature = -17.5 ° C…

Q: Steam enters the condenser of a steam power plant at 30 kPa, a quality of 91 % and a mass flow rate…

A: . .

Q: The interior of a refrigerator has a surface area of 6.2 m2 . It is insulated by a 2 cm thick…

Q: An air-cooled condenser has an expected h value of 30 W/m2-K based on the air-side area. The…

A: Given data-W=30 w/m2heat transfer= 60 kwTi=entering temp=48°Cm=15 kg/s

Q: stainless steel plate at 100◦C faces a firebrick wall at 500◦C.Esti- mate the heat flux and…

A: Solution as follows

Q: An electric motor is to be connected by a horizontal steel shaft (k 42.56 W/m.K), 25 mm in diameter…

A: According to the given information, the diameter of shaft d is 25mm, the impeller of a pump,…

Q: The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that…

Q: Two Carnot heat engines operate between the heat reservoirs as shown. If one engine has triple…

A: The thermal efficiency for left side Carnot heat engine is written as,…

Q: Compare an SHS with a solid storage material and an LHS with a PCM storage material. The thermal…

A: Given, Thermal capacity of energy storage system:-Q=600KWhQ=600×3600Q=2160000KJFor SHS,Density of…

Q: Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser…

Q: Q26:- 34 °API gas oil at 80 °F is being pumped from a storage tank on the ground to another tank…

A: Given: The API = 34 The temperature, T = 80 F The height of the hill, H = 390 ft The mass flow rate…

Q: An office space of 15 ft x12 ft x10 ft height. The heat loss through roof is (8820 Btuh) if…

Q: 16. At winter design conditions, a house is projected to lose heat at a rate of 60,000 Btu/h. The…

A: Given :- Rate of heat Loss = 60000 Btu/h Internal heat gain = 6000 Btu / h To find :- Required…

Q: In a fossil fuel power plant the chemical energy stored in fossil fuels such as coal, fuel oil,…

A: GIVEN; Coal-fired plant with a capacity of 100 MW = 100×106 W 60% efficiency (40% is lost as heat)…

Q: If you add heat of magnitude 800 kJ to a mass of 800g of water originally at a temperature 75…

A: GivenQ=800kJm=800g=0.80kgTi=75oCLHV=22.6×105 J/kg=2260 kJ/kgCp=4186 J/kgK=4.186 kJ/kgK

Q: A refrigerator used to cool a computer requires 3 kW of electrical power an Calculate the cooling…

A: Given Data⇒ Work inputW=3 kW COP=1.4 Cooling effect=?

Q: The temperature difference for the purpose of domestic hot water is in the range اخترأحد الخيارات a.…

A: Domestic hot water is used in household for sanitation, clothing, personal hygiene , food…

Q: The outside air at 31 C dry bulb temperature and 18.5 C wet bulb temperature enters a cooling coil…

A: Write the given values along with the suitable variables.

Q: A refrigeration system uses a water-cooled condenser for rejecting the waste heat. The system…

A: Given data The heat absorbed by the system is qL=21000 Btuh The rate of water flow is m˙=1.45…

Q: Building requires average 200kg of hot water at temperature 50 oC per day. Specific heat of water…

A: heat required per day to heat 200 kg of water to 50 celcius from 10 degrees = 200*4185.5 * ( 50-20)…

Q: An automobile engine consumes fuel at a rate of 22 L/h and delivers 55 kW of power to the wheels. If…

A: Given data: Fuel consumption rate = 22 L/hr Brake power = 55 kW…

Q: What is the heat transfer rate of initial temperature of 26 degree Celsius and the final temperature…

Q: The head of the de partment in the company that you are working in asked you to make use chart…

A: Given m=0.1 kg/s Required 1.) RE 2) Heat Rejection 3) Power

Q: (i) What is a thermal energy reservoir? Give some examples.

A: Thermal energy reservoir: Thermal energy reservoir is a body with very large heat capacity that can…

Q: n electric generator at a power plant produces energy by passing superheated steam from a high…

A: Carnot cycle is a type of energy producing device which consists of 4-processes:- Isentropic…

Q: 0.39) Q2/ The outside air at 31°C dry bulb temperature and 18.5°C wet bulb temperature enters a…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Question

. A pump is used for pumping water from lake at height of 100 m consuming power of 60 kW. Inlet pipe and exit pipe diameters are 150 mm and 180 mm respectively. The atmospheric temperature is 293 K. Determine the temperature of water at exit of pipe. Take specific heat of water as 4.18 ??/??. ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop systems.
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
Water with a specific heat of 1 BTU/lbmoF is pumped using a 1-hp jet pump from a well that is 20 ft deep into a vented water vessel 160 ft above the ground. In the process, 400 BTU/min of heat is lost from the system. What is the temperature (oF) of the water as it enters the vessel if the flow rate of the water is 5 gal/min? Assume the temperature of water in the well is (35oF).
Q29. Steam enters the condenser of a power plant at 3 psia and a quality of 95% with a ratio ofmass flow of 40,000 lbm/hr. It will be cooled with water from a nearby river, which will circulate through the tubes inside the condenser. In order to avoid thermal pollution, the river water is not allowed to suffer from an increase in temperature.temperature greater than 18°F. If steam is to leave the condenser as a saturated liquid at 3 psia, determine how many times the mass flow rate of steam will be the mass flow rate of water, as well as the heat transfer from one system to the other.
The sun generates an average of 1.958 kW/m2 when tapped as source of energy wherein a flat-plate collector with an area of 1.006 m2 is used. If the flow rate of water inside the collector is 50.1 liters per hour, compute for the possible temperature rise of working fluid in K.
Determine the power required for a forced draught and induced draught fan in a boiler having coal consumption of 25 kg/min and air/fuel ratio of 19 by mass. The ambient air temperature and hot gas temperature at exit are 30C and 140 C respectively. Draught required is equivalent to 32.2 mm of water and mechanical efficiency of motor/fan is merely 70%alz
A pump is used for pumping water from lake at height of 100 m consuming power of 60 kW. Inlet pipe and exit pipe diameters are 150 mm and 180 mm respectively. The atmospheric temperature is 293 K. Determine the temperature of water at exit of pipe. Take specific heat of water as 4.18 kJ/kg. K
What refrigeration capacity in TOR is required to cool 2000 cfm of air from 85°F to 70°F? If the specific heat ratio (k) and specific gas constant (R) of air are 1.4 and 0.28708 kJ/kg-K, respectively.
1.) Determine the refrigerant name and chemical formula of R-22 2.) An ice plant produces 20 tons of ice per day at -15oC from water at 25 oC. If miscellaneous losses are 12 % of the freezing and chilling load, calculate the refrigeration capacity of the plant, in TR.
A Carnot engine receives 100 Btu of heat from a reservoir at 600oF and ejects at 60 Btu of heat. Calculate the temperature of the cold reservoir in oF.
Solve for the latent heat of water at Tw = 28C(and. λw = 2435 kJ/kg)
A completely insulated mixing vessel is designed to deliver water at 60 ⁰Cand atmospheric pressure at a rate of 4 kg/s by mixing two streams of incomingwater in an environment at 25 ⁰C. Saturated steam at atmospheric pressure isinserted on the hot side. Two options are being considered for the cold side: (a)chilled water from the plant at 3 ⁰C or (b) water from the tap at 20 ⁰C (both atatmospheric pressure). 1. Determine the thermal efficiency of each process