"Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285 K and hot reservoir at 350 K. It is also equipped with a metal can cylinder that has a volume of 0.0002 m3. What is the total volume of air in the system if the metal can cylinder is in the hot reservoir and the measured pressure and height of the piston are 103850 Pa and 60 mm, respectively?" O 4.25x10-2 m3 O 3.70x10-4 m3 O 2.42x10-4 m3 O 4.24x10-5 m3

"Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285 K and hot reservoir at 350 K. It is also equipped with a metal can cylinder that has a volume of 0.0002 m3. What is the total volume of air in the system if the metal can cylinder is in the hot reservoir and the measured pressure and height of the piston are 103850 Pa and 60 mm, respectively?" O 4.25x10-2 m3 O 3.70x10-4 m3 O 2.42x10-4 m3 O 4.24x10-5 m3

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.39P: The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must...

See similar textbooks

Similar questions

2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
The tip of a soldering iron consists of a 0.6-cm- diameter copper rod, 7.6 cm long. If the tip must be 204C, what are the required minimum temperature of the base and the heat flow, in watts, into the base? Assume that h=22.7W/m2KandTair=21C.
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
2.55 A long, 1-cm-diameter electric copper cable is embedded in the center of a 25-cm-square concrete block. If the outside temperature of the concrete is 25oC and the rate of electrical energy dissipation in the cable is 150 W per meter length, determine temperatures at the outer surface and at the center of the cable.
A cylindrical liquid oxygen (LOX) tank has a diameter of 1.22 m, a length of 6.1 m, and hemispherical ends. The boiling point of LOX is -179.4C. An insulation is sought that will reduce the boil-off rate in the steady state to no more than 11.3 kg/h. The heat of vaporization of LOX is 214 kJ/kg. If the thickness of this insulation is to be no more than 7.5 cm, what would the value of its thermal conductivity have to be?
Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
Consider a heat engine with a piston chamber that has a diameter of 30 mm, a cold reservoir at 285 K and hot reservoir at 350 K. It is also equipped with a metal can cylinder that has a volume of 0.0002 m3. How many moles of air are present in the system if the metal cylinder is in the cold tank and the measured pressure and the total air volume are 104160 and 0.00015 m3, respectively?
THERMOFLUID A student living in a 3-m X 4-m X 4-m dormitory room turns on her 100-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and heat trans windows are tightly closed and disregarding any heat fer let through the walls and the windows, determine the temperature in the room when she comes back 8 h later. Use specific heat values at room temperature, and assume room to be at 100 kPa and 20°C in the morning she leaves.
Located near the bottom of an insulated cylinder is a rigid plate. Between the rigid plate and the bottom of the cylinder is 0.4 kg (ma) of air at 250 kPa (Pa1) and 300 K (Ta1). Between the rigid plate and a moveable piston 0.5 kg (mw) of superheated water vapor at 300 Celsius (Tw1) and 100 kPa (Pw1) is added. Consider these to be the initial conditions (state 1) of this multi-component system. The rigid plate is conductive allowing heat to pass between the air and water vapor, but the piston is well insulated. The water vapor is manually compressed in an unknown process until the volume of water vapor (Vw2) is halved and the pressure is 200 kPa (Pw2), at which point the air and water vapor are in temperature equilibrium.Determine the following:A. The change in entropy of air and water in kJ/K B. The change in entropy of the combined system, S2-S1, in kJ/K, neglecting the mass of the rigid plate C. The entropy produced, σ, of the combined system during the process
A mass of 300kg of oil is cooled in 1 hour from 70 celcius to 35 celcius in a cooler consisting of a bank of tubes through which hot oil passes. Cooling water circulates around the outside of the tubes. Calculate the mass of cooling water required per hour if the water temp increases by 21 degrees celcius . Specific Heat of Oil - 2.0 kJ/kg deg C Specific Heat of Water - 4.186 kJ/kg deg C